Sewing Machine Troubleshooting

Sewing Machine Not Picking Up the Bobbin Thread: Causes and Fixes

If the needle won't pick up the bobbin thread, check how you draw it up, then the needle, threading and bobbin, before suspecting timing. Step-by-step fixes.

On this page
  1. Two Different Problems
  2. How to Bring Up the Bobbin Thread Correctly
  3. Check 1: The Needle
  4. Check 2: Rethread the Top
  5. Check 3: The Bobbin
  6. Check 4: Clean the Hook Area
  7. Check 5: Fabric and Needle Match
  8. If None of That Works: Needle Bar Height and Timing

Two Different Problems

“Not picking up the bobbin thread” can describe two situations:

  1. The bobbin thread won’t come up when you turn the handwheel to draw it through the needle plate before you start.
  2. Stitches don’t form while sewing. The top thread goes in and out of the fabric without locking with the bobbin thread, or stitches are skipped.

The causes overlap heavily, so the checks below cover both. Work through them in order. The first few fix most cases.

How to Bring Up the Bobbin Thread Correctly

On machines where you need to draw the bobbin thread up:

  1. Thread the top and insert the bobbin as your manual shows.
  2. Raise the presser foot.
  3. Hold the end of the top thread lightly in your left hand. Keep it slightly taut, not pulled tight.
  4. Turn the handwheel toward you one full turn, so the needle goes down and comes back up to its highest point.
  5. Pull gently on the top thread. A loop of bobbin thread should come up through the needle plate.
  6. Use scissors or a pin to pull the loop out, then lay both threads under the foot toward the back.

If you don’t hold the top thread, it can go slack and the hook may not catch it properly. Turning the wheel the wrong way, away from you, can also stop it working and may tangle the thread around the hook.

Machines that don’t need it drawn up

Many modern drop-in bobbin machines have a “quick-start” or “quick bobbin” system: you drop the bobbin in, guide the thread through the slot, and cut it at the built-in cutter. The machine catches the bobbin thread on the first stitch. If your machine works like this, you don’t need to draw the thread up, and failing to see a loop when you try is not a fault. Check your manual.

Check 1: The Needle

The needle is the most common culprit:

  • Backwards. On most modern home machines the flat side of the needle shank faces the back. If the needle is turned around, the hook can’t find the thread loop, which forms on the wrong side, and no stitch forms. Some older machines take the needle facing sideways, so check your manual.
  • Not pushed fully up. A needle sitting even slightly low changes where the loop forms. Push it up as far as it will go and tighten the clamp.
  • Bent or blunt. Replace it. A bent needle can pass too far from the hook.
  • Wrong type. On knits, a ballpoint or stretch needle helps the loop form reliably. A universal needle sometimes skips on elastic fabrics.

Check 2: Rethread the Top

Raise the presser foot (which opens the tension discs) and rethread completely from the spool. Make sure the thread passes through the take-up lever and that the needle is threaded in the direction your manual shows, front to back on most machines. Also check the thread hasn’t wrapped around a guide or the take-up lever, which can hold it too tight for a loop to form. Upper tension set very high can have the same effect, so set it back to the general-purpose setting.

Check 3: The Bobbin

  • Right type. Bobbins are not universal. Different machines use different classes and sizes, and plastic and metal bobbins are not always interchangeable. A bobbin that “nearly fits” may wobble and cause pickup problems. Use the one your manual specifies.
  • Inserted correctly. Check the direction it should unwind, and that the thread has gone through the tension slot or under the spring.
  • Wound evenly. A lumpy or loose bobbin can snag. Rewind if needed.
  • Enough thread. An empty or nearly empty bobbin is easy to overlook.
  • Case seated. On front-loading machines the bobbin case should click home. On drop-in machines the case should sit flat with any locating tab in its notch.

Check 4: Clean the Hook Area

Lint and thread scraps around the hook and bobbin case can stop the bobbin turning freely or interfere with the hook. Unplug the machine, remove the needle plate and bobbin case if your manual allows, and brush everything clean. Look for burrs on the bobbin case or plate where the needle may have struck. These can catch the thread.

Check 5: Fabric and Needle Match

When sewing thick fabric, such as many quilt layers or jeans seams, the fabric can grip the needle and thread so tightly that the loop doesn’t form, and stitches skip. Use a heavier needle designed for the fabric, slow down, and hand-turn over the thickest parts. See our guide to sewing through thick fabric.

Very fine or stretchy fabric can also flex up and down with the needle, which disrupts the loop. A fresh fine needle, a stabiliser underneath, or a straight-stitch plate (for straight stitching only) can help.

If None of That Works: Needle Bar Height and Timing

If a new needle of the right type, correct threading, the correct bobbin and a clean hook area don’t fix it, the problem may be mechanical:

  • Needle bar height. If the needle bar has moved up or down, the needle’s eye no longer lines up with the hook’s path. It can be knocked out of place by a needle strike.
  • Hook timing. If the hook reaches the needle too early or too late, it misses the loop. Timing can slip after a hard jam or striking a pin.

These are often linked and usually need tools and the service manual to correct. Our guide to sewing machine timing symptoms and checks explains how to tell whether timing is likely to be the problem and what’s involved. If stitches form but tangle into a mass under the fabric, see how to fix bird’s nesting instead.

The complete guide to sewing machine troubleshooting

Sewing Machine Troubleshooting: Fixing Common Stitch Problems
Read the guide

Keep exploring

Guides from other topics

All topics →