Sewing Basics

How to Wind and Insert a Bobbin

How to wind a bobbin and insert it in drop-in and front-loading machines, including Singer and White models, plus which way it faces and fixes for bunching.

On this page
  1. Identify Your Bobbin System
  2. How to Wind a Bobbin
  3. Inserting a Drop-In (Top-Loading) Bobbin
  4. Inserting a Front-Loading Bobbin and Case
  5. Which Way Should the Bobbin Face? Clockwise or Anticlockwise?
  6. Putting a Bobbin in a Singer Sewing Machine
  7. White Sewing Machine Bobbin Instructions
  8. How to Put a Bobbin Case Back Together
  9. Why Is Thread Bunching Underneath?
  10. What Happens If You Sew Without a Bobbin?

The bobbin supplies the lower thread for every stitch. If it’s wound unevenly, turning the wrong way, or not clicked under its tension spring, you’ll see loops, tangles or skipped stitches no matter how well the top is threaded. Here’s how to wind a bobbin and insert it correctly on the two main types of home machine.

Identify Your Bobbin System

Look at the area under the needle:

  • Drop-in (top-loading): a clear plastic cover sits flat in the bed in front of the needle. The bobbin drops in from above, and the bobbin case usually stays in the machine. This is common on many current Singer, Brother and Janome machines, among others.
  • Front-loading (vertical): there’s a door or removable tray below the needle at the front, and inside it a metal bobbin case that you pull out. This style is found on many vintage machines and some current mechanical and higher-end models.

Before you start, make sure you have the right bobbins for your machine. Similar-looking bobbins can cause problems. See how to know what bobbin to use.

How to Wind a Bobbin

  1. Put the thread spool on the spool pin and add the spool cap.
  2. Lead the thread around the bobbin-winding tension guide. This is usually a small disc on the top of the machine. It’s what makes the bobbin wind firmly and evenly.
  3. Wrap the thread around an empty bobbin several times, in the direction your manual shows. Some bobbins have a small hole, and you can pass the thread end through it from the inside.
  4. Place the bobbin on the winder spindle and push it into the winding position, usually to the right.
  5. Hold the thread tail and press the pedal or the start button. After a few turns, stop and trim the tail close to the bobbin.
  6. Continue winding. Many machines stop automatically when the bobbin is full. If yours doesn’t, stop before the thread reaches the rim.
  7. Push the spindle back, remove the bobbin and cut the thread.

On many machines, the needle doesn’t move while you wind. On older machines you may need to loosen the handwheel’s inner knob first. Your manual will say. Remember to tighten it again afterwards; if the needle won’t move later, see motor runs but the needle won’t move.

Signs of a poor wind: the thread is loose and spongy, it’s piled to one side, or it’s wound over the rim. Wind it again, making sure the thread is in the tension guide.

Inserting a Drop-In (Top-Loading) Bobbin

  1. Raise the needle to its highest position and raise the presser foot. Turn the machine off if your manual recommends it.
  2. Remove the bobbin cover. Usually you slide a release button, and the clear plate pops up.
  3. Drop the bobbin in so the thread unwinds in the direction shown on the diagram near the bobbin area. On many drop-in machines this is counterclockwise: looking down, with the thread end pulled toward you, the bobbin and thread form a shape like the letter “P”.
  4. Hold the bobbin down lightly with a finger and pull the thread through the notch, then along the guide channel. You should feel it click under the tension spring.
  5. Leave a tail of about 10–15 cm. Many machines have a built-in cutter at the end of the channel.
  6. Replace the cover.

Many drop-in machines don’t need you to pull the bobbin thread up before sewing, but follow your manual.

Inserting a Front-Loading Bobbin and Case

  1. Raise the needle to its highest position and open the bobbin door.
  2. Remove the bobbin case by pulling out the small hinged latch on the front, then drawing the case straight out. If you keep the latch open, the bobbin stays inside.
  3. Insert the bobbin into the case. On most front-loading cases, when you hold the case with its open side facing you, the thread should unwind clockwise. Check your manual: this is the step that varies most.
  4. Pull the thread into the slot on the edge of the case, then draw it under the tension spring until it comes out of the small opening at the end of the spring.
  5. Check it: pull the thread gently. The bobbin should turn in the expected direction with light, even resistance.
  6. Reinsert the case. Hold it by the open latch, line up the finger or tab on the case with the notch at the top of the hook area, and push it in until it clicks. Release the latch.
  7. Bring up the bobbin thread: hold the upper thread, turn the handwheel toward you one full turn, and pull up the loop.

If the case isn’t fully seated, the needle can hit it. Push until you hear or feel the click, and turn the handwheel slowly by hand for the first stitch.

Which Way Should the Bobbin Face? Clockwise or Anticlockwise?

It depends on the system and the machine, so there is no universal answer:

  • Many drop-in machines: the thread unwinds counterclockwise, as seen from above.
  • Many front-loading cases: the thread unwinds clockwise, with the open side of the case facing you.

The reliable answer is the small diagram near the bobbin area, or in your manual. If the bobbin is in the wrong way, the lower tension can be wrong or the thread may not catch properly, which often shows as loose or looped stitches.

Putting a Bobbin in a Singer Sewing Machine

Most current Singer home machines have a top drop-in bobbin. Singer’s help centre describes the drop-in process this way: raise the needle, slide the release button to remove the cover plate, and drop the bobbin in so the thread unwinds counterclockwise. Then guide the thread through slot A and around to slot B until it clicks, pull out about 15 cm of thread, and replace the cover.

Older and some heavy-duty or vintage Singer models use a front-loading metal bobbin case and follow the front-loading steps above. If you’re not sure which you have, check the model number on the machine and look up the manual on Singer’s support site.

White Sewing Machine Bobbin Instructions

White machines were made over many decades, and their bobbin systems vary by model. Some use front-loading metal bobbin cases and others use drop-in bobbins. The steps above apply to both:

  • Front-loading White machines: remove the case by its latch, insert the bobbin in the direction shown in the manual, pull the thread through the slot and under the tension spring, and click the case back in.
  • Drop-in White machines: remove the cover, drop the bobbin in following the printed diagram, guide the thread through the channel, and replace the cover.

The bobbin type also varies, so match the bobbin to the one that came with your machine or to your manual. If you don’t have the manual, the model number (usually on a plate on the back or underside) helps you find one online or at a dealer.

How to Put a Bobbin Case Back Together

If a front-loading bobbin case has come apart (usually the latch or the tension spring), compare it with a photo or diagram in your manual before you reassemble it. The tension spring is held by a small screw. Its tension is set at the factory, so change it only in very small turns, and note the original position. A bent spring or a burr on the case can cause ongoing thread problems. Replacement bobbin cases for common machines are widely available, and sometimes replacing the case is the simplest fix.

Drop-in machines have a bobbin case seated in the hook area. If you’ve removed it for cleaning, line it up with the stopper notch shown in your manual so it can’t rotate, then put the needle plate back on.

Why Is Thread Bunching Underneath?

A tangle under the fabric, often called a “bird’s nest”, is usually caused by the upper thread, even though it shows up on the bottom. Check these in order:

  1. Rethread the top with the presser foot up, making sure the thread goes through the take-up lever. See how to thread a sewing machine.
  2. Reinsert the bobbin in the correct direction, clicked under the tension spring.
  3. Hold both thread tails for the first couple of stitches.
  4. Clean lint from the bobbin area.
  5. Check the bobbin type and wind. A loose wind or the wrong bobbin can cause problems.
  6. Put in a new needle, the right size for the fabric.

This applies to Singer and most other brands. For more fixes, see our full guide to thread bunching underneath.

What Happens If You Sew Without a Bobbin?

Without a bobbin thread for the upper thread to lock around, the machine can’t form a lockstitch. The needle punches holes, and the upper thread may form loose loops that pull straight out, or tangle around the hook. Stop as soon as you notice. Remove the fabric, clear any tangled thread, put a wound bobbin in, and rethread.

Once the bobbin is in, our beginner’s guide to using a sewing machine takes you through your first seam.

The complete guide to sewing basics

How to Use a Sewing Machine: A Complete Beginner's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →