Sewing Machine Troubleshooting

Sewing Machine Timing Off? Symptoms, Checks and How to Reset It

Sewing machine timing off? Learn the symptoms, the simpler causes to rule out first, how to check needle-to-hook timing and what resetting it involves.

On this page
  1. What “Timing” Means on a Sewing Machine
  2. Symptoms That Point to Timing
  3. Rule These Out First
  4. How to Check the Timing
  5. Why Timing Slips
  6. Timing, Needle Bar Height and Hook Clearance
  7. How Timing Is Reset
  8. When to Use a Technician

What “Timing” Means on a Sewing Machine

A lockstitch machine forms each stitch by passing the top thread around the bobbin thread. The needle carries the top thread down through the fabric. As it starts to rise again, friction against the fabric makes the thread form a small loop at the back of the needle. The point of the hook (the part that spins or rocks around the bobbin) has to pass through that loop at exactly the right moment, catch it and carry it around the bobbin.

“Timing” is the relationship between the needle’s position and the hook’s position. If the hook arrives too early, the loop hasn’t formed yet. If it arrives too late, the loop has already shrunk back up. Either way the hook misses it and no stitch forms.

Timing is fixed in the factory and normally stays put for years. It can slip, but it’s a less common cause of stitch problems than most people think. Most “timing” faults turn out to be a needle, threading or bobbin issue.

Symptoms That Point to Timing

These symptoms suggest timing may be off, especially if several appear together or started suddenly after a jam:

  • Skipped stitches on every fabric, even with a new needle and correct threading.
  • No stitches at all. The top thread goes in and out of the fabric but never locks with the bobbin thread. See why the machine won’t pick up the bobbin thread for the simpler causes of this.
  • Zigzag catching on one side only. Stitches form on one swing of the needle but not the other, so a zigzag looks like a straight or broken line. See why a zigzag only sews straight.
  • A clicking, ticking or clunking sound each time the needle goes down, as if metal is touching metal.
  • Needles bending or breaking repeatedly, or a needle with a shiny scrape mark on one side where the hook has rubbed it.
  • Thread shredding or snapping where the hook is catching the thread at the wrong point.

Symptoms that usually aren’t timing

  • Loops or “bird’s nests” under the fabric. These are almost always caused by the top threading or tension. See how to fix thread bunching underneath.
  • Loose or tight stitches that change when you adjust the tension dial.
  • Problems on one fabric only, such as knits or very thick seams. That points to the needle type or fabric handling.
  • A machine that won’t turn at all. That’s a jam, not timing. See clearing a jammed machine.

Rule These Out First

Do all of these before you touch any internal screws. They’re quick and they fix most cases.

  1. Fit a brand-new needle. A slightly bent or blunt needle mimics timing faults very closely.
  2. Check the needle system. Most home machines take 130/705H needles (also sold as 15x1 or HAx1). Industrial or some vintage needles of the wrong system sit at a different height and will skip. See whether all needles fit all sewing machines.
  3. Insert it correctly. On most modern machines the flat side of the shank faces the back. Push it all the way up before tightening the clamp. A needle sitting even a millimetre low changes where the loop forms.
  4. Match the needle to the fabric. Use a ballpoint or stretch needle on knits and a jeans needle on denim.
  5. Rethread the top with the presser foot raised.
  6. Use the correct bobbin for your machine, inserted the right way.
  7. Clean the hook area. Packed lint can stop the bobbin case sitting in the right place.
  8. Check the needle plate and bobbin case for burrs where a needle has struck. Burrs catch thread.

If the problem is still there after all of this, a timing check is worth doing.

How to Check the Timing

You can look at the timing without adjusting anything. The details vary by machine, but the general method is:

  1. Unplug the machine.
  2. Fit a new needle and select a straight stitch with the needle in the centre position.
  3. Remove the presser foot, the needle plate and the bobbin (and the bobbin case, if your manual says it can come out). On some drop-in bobbin machines you’ll see more of the hook if you also take off the bottom cover.
  4. Turn the handwheel slowly toward you until the needle reaches its lowest point.
  5. Keep turning so the needle rises a short distance, typically around a couple of millimetres. This is the moment the loop forms.
  6. Watch the hook point. At this moment it should be passing behind the needle, very close to it, a little above the top of the needle’s eye, in the scooped-out area on the back of the needle called the scarf.

If the hook point is clearly ahead of the needle or behind it at this moment, or passes well above or below the eye, the timing (or the needle bar height) is likely off. The exact rise and height figures are specified in the service manual for each model.

Check at both sides of a zigzag

On zigzag machines, repeat the check with the widest zigzag. Hand-turn through several stitches and look at the hook as the needle comes down on the left and on the right. The hook should pick up the loop at both positions. A machine that is slightly out of time often still sews a straight stitch but misses on one side of a zigzag.

Why Timing Slips

Timing is usually held by set screws, a gear or a toothed belt. It can slip when the machine is stopped suddenly while the motor is still driving:

  • A hard thread jam in the hook area, especially if you kept pressing the pedal.
  • The needle striking a pin, a thick seam or the needle plate.
  • Turning the handwheel the wrong way with thread caught in the hook.
  • Forcing the machine through layers too thick for it. See getting a machine through thick fabric.

Some machines are designed to protect themselves with a safety clutch that slips under a jam. This can sometimes be reset by following the manual. Over time, timing can also drift through worn teeth on an internal timing belt, cracked or worn gears (some older models use plastic or nylon gears that become brittle) or a set screw that has worked loose.

Timing, Needle Bar Height and Hook Clearance

People often call any of these “timing”, but they’re three separate adjustments:

  • Hook timing. When the hook point reaches the needle.
  • Needle bar height. Where the needle’s eye sits in relation to the hook’s path. If the needle bar has been knocked up or down, the hook passes too high or too low even if the timing is right.
  • Hook-to-needle clearance. How close the hook point passes behind the needle. Too far and it misses the loop. Too close and it strikes or scrapes the needle.

They affect each other. Changing the needle bar height changes the point at which the hook seems to meet the eye. That’s why service manuals set them in a specific order and why a technician checks all three together.

How Timing Is Reset

Resetting timing is a precise mechanical job. On many machines it’s possible at home with patience, the right screwdriver and the service manual (sometimes called an adjuster’s manual) for your model. On others, especially computerised machines, it’s best left to a technician. If your machine is under warranty, opening it may affect that, so check first.

Before you start

  • Unplug the machine throughout.
  • Take photos before you loosen anything.
  • Mark the shaft and the part with a fine marker so you can return to the original position if things get worse.
  • Change one thing at a time, and re-check after each change.
  • Don’t loosen screws you can’t identify. Some screws set the shaft end play or feed and aren’t related to timing.

The general procedure

This is an outline of what’s typically involved. The actual screws, measurements and order depend on the machine.

  1. Fit a new, correct needle, set a centre straight stitch and remove the plate and bobbin parts as for the check above.
  2. Check the needle bar height first if the service manual calls for it, and correct it if needed.
  3. Turn the handwheel to the specified position: the needle at its lowest point, then rising by the amount the manual gives.
  4. Locate the adjustment. Depending on the design, this could be the set screws holding the hook, or the gear driving the hook, on the lower shaft. On some machines it’s the position of a toothed belt on its pulley.
  5. Loosen the screws just enough for the part to turn on its shaft with firm pressure.
  6. Hold the needle in position and rotate the hook until its point is at the needle’s centreline, just above the eye, at the specified clearance.
  7. Tighten the screws firmly, then re-check. Parts often shift slightly as screws are tightened.
  8. Check at the left and right zigzag positions, then sew a test on a scrap of fabric.

Older machines with a long bobbin shuttle (a “bullet” shuttle, as on many vintage Singers) or a front-loading oscillating hook use different mechanisms. The principle is the same, but the procedure isn’t.

When to Use a Technician

Book a service if:

  • You’ve worked through the rule-out list and the problem persists, but you’re not comfortable opening the machine.
  • The machine is computerised, under warranty, or has a horizontal hook you can’t reach without major disassembly.
  • The timing slipped once and then slipped again soon after resetting. That can mean a worn belt, a damaged gear or a hook with a burr on its point.
  • You hear grinding, or the hook point looks chipped or rough.

A technician can usually check timing, needle bar height and clearance together as part of a routine service. See how often to service a sewing machine for typical intervals.

The complete guide to sewing machine troubleshooting

Sewing Machine Troubleshooting: Fixing Common Stitch Problems
Read the guide

Keep exploring

Guides from other topics

All topics →