Sewing Machine Troubleshooting

Why Your Sewing Machine Needle Keeps Breaking

Sewing machine needles snapping? Learn the common causes, from pulling fabric and pins to the wrong foot, plus what to do right after a needle breaks.

On this page
  1. What a Broken Needle Usually Means
  2. What to Do Right After a Needle Breaks
  3. The Most Common Causes
  4. Breaks in the Same Place Every Time
  5. How Often Should You Replace Your Needle?
  6. Preventing Broken Needles

What a Broken Needle Usually Means

A sewing machine needle breaks when it is bent sideways into something hard, usually the needle plate, the presser foot, a pin or the bobbin case, or when it is forced through more fabric than it can handle. In most cases the cause is in how the fabric is handled or how the machine is set up, not a fault inside the machine. A needle that breaks repeatedly, especially in the same spot, is a sign that something needs correcting before you sew on.

What to Do Right After a Needle Breaks

  1. Stop and switch off the machine, then unplug it.
  2. Find all the pieces. Look on the fabric, the bed of the machine and the floor. A missing tip may have dropped through the plate hole.
  3. Remove what’s left of the needle. Hold it as you loosen the clamp screw so it doesn’t fall in.
  4. Check the bobbin area. Remove the needle plate and bobbin case and look for fragments. A piece left inside can jam the hook or damage it. If a piece has dropped somewhere you can’t reach, many manufacturers’ support pages explain how to retrieve it for specific models, or a technician can.
  5. Check for damage. Run a fingernail gently around the needle hole and under the presser foot. A needle strike can raise a burr that will cut thread later.
  6. Fit a new needle and turn the handwheel by hand through a full stitch to check it clears everything.

Needle fragments can fly, so keep your face back from the needle when sewing heavy layers. Some sewists wear safety glasses for heavy-duty work.

The Most Common Causes

Pulling or pushing the fabric

This is the most common cause. If you pull the fabric toward you or push it away while the needle is in it, the needle bends. On its next downstroke it can hit the needle plate and snap. Let the feed dogs move the fabric. Your hands should only guide it.

Sewing over pins

If the needle lands on a pin it can break, and sometimes sends the pin or needle tip into the bobbin area. Remove pins just before they reach the presser foot. Placing pins at right angles to the seam, with heads toward the edge, makes them easier to pull out as you go. Some sewists use clips instead.

Needle too fine for the fabric

A fine needle in denim, canvas or many layers flexes and breaks. Use a size and type to suit the fabric. Heavy fabrics usually call for something like a 90/14 to 110/18 jeans or denim needle, which has a stronger shaft and sharper point. See our guide to sewing through thick fabric for more.

Needle not fully inserted or loose

If the needle isn’t pushed all the way up into the clamp, it sits too low and can hit the hook or bobbin case. If the clamp screw is loose, the needle can work its way down while you sew. Push the needle up as far as it will go, with the flat side of the shank facing the way your manual shows (usually the back on modern home machines), and tighten the screw firmly. Recheck it now and then, as vibration can loosen it. Our guide to changing a sewing machine needle shows each step.

Wrong foot or plate for the stitch

Feet and needle plates have openings sized for the stitch they are designed for. A straight-stitch foot or straight-stitch needle plate has only a small hole in the centre. If you select a zigzag, a decorative stitch, or move the needle position left or right while one of these is fitted, the needle will hit it and break. The same applies to some specialty feet. Always check the foot and plate suit the stitch width before you start. Turn the handwheel by hand through the first stitch or two to confirm the needle clears.

Some computerised machines let you set a straight-stitch plate or foot mode that limits the stitch width; use it if yours has one.

Twin needles and wide stitches

A twin or double needle is wider than a single needle. If the stitch width is too wide, one of the two needles will hit the foot or plate. Many machines have a twin-needle setting that restricts width. If yours doesn’t, keep the width narrow and test by turning the handwheel slowly by hand first.

Thick seams and bulky layers

When the presser foot climbs onto a thick seam, such as a jeans hem, it tilts. The needle can then strike at an angle and deflect. Slow down, use the handwheel over the bulkiest part, and level the foot with a hump jumper or a folded piece of fabric behind the seam.

Bobbin case not seated

If the bobbin case, or a drop-in case’s tab, isn’t seated properly, it can shift into the needle’s path. If the needle breaks soon after you change the bobbin, remove it and reinsert the case carefully. Check the case for a fresh nick where the needle may have struck it.

Wrong needle system

Most home sewing machines use a standard flat-shank needle system (often labelled 130/705 H or 15x1). Industrial machines, overlockers and some specialist or vintage machines use different systems. A needle that fits the clamp but is the wrong length can sit too high or too low. Check your manual for the correct system, and see whether all sewing machine needles fit all machines for how the systems differ.

Breaks in the Same Place Every Time

If a correctly installed new needle breaks or chips at the same moment in every rotation, often with a sharp click as it hits something underneath, the needle may be striking the hook. This can point to:

  • a bent needle bar or needle clamp (often after a hard strike)
  • a damaged or misaligned bobbin case
  • hook timing that has slipped

Stop sewing. Turn the handwheel slowly by hand, with the plate removed if possible, and watch where the needle touches. If it’s the hook, see our guide on timing symptoms and checks. This is usually a job for a technician.

How Often Should You Replace Your Needle?

A common guideline is to fit a new needle after roughly 6 to 8 hours of sewing, at the start of each new project, and always after it has hit a pin or anything hard. A blunt needle makes the machine work harder to pierce the fabric, which increases the chance of deflection and breakage. Signs of a dull needle include a popping or thumping sound as it enters the fabric, skipped stitches, and pulled threads or small holes in fine fabric.

Preventing Broken Needles

  • Let the feed dogs move the fabric; don’t pull it.
  • Remove pins before the foot reaches them.
  • Match the needle type and size to the fabric.
  • Check the foot and plate suit the stitch width, especially after changing stitches.
  • Push the needle fully up and keep the clamp screw tight.
  • Slow down over thick seams.
  • Change the needle regularly.

If thread keeps breaking but the needle survives, see why your thread keeps breaking instead. If the machine is also making a loud knocking sound, see why your sewing machine is banging.

The complete guide to sewing machine troubleshooting

Sewing Machine Troubleshooting: Fixing Common Stitch Problems
Read the guide

Keep exploring

Guides from other topics

All topics →