Fabrics and Needles

Sewing Stretchy and Tricky Fabrics on a Sewing Machine

How to set up a regular sewing machine for knits and other awkward fabrics: needles, stitches, thread, foot pressure, fixes, and which machine features help.

On this page
  1. Why stretch and “tricky” fabrics give home machines trouble
  2. The four-part setup for stretch fabric
  3. Step-by-step: sewing a knit seam on a regular machine
  4. Hemming knits without a coverstitch machine
  5. Common stretch-sewing problems and fixes
  6. What is the best sewing machine for stretch fabrics?
  7. Other tricky fabrics, and where to start with each
  8. General habits that help with any difficult fabric

Why stretch and “tricky” fabrics give home machines trouble

A household sewing machine is built around one assumption: the fabric under the needle is a stable woven that feeds evenly and stays put while the stitch forms. Most problems with “difficult” fabrics come from breaking that assumption in one of three ways:

  • The fabric moves when it shouldn’t. Knits stretch as the feed dogs push them, so seams ripple. Slippery fabrics shift between layers. Pile fabrics like minky creep.
  • The fabric resists the needle. Denim, canvas and leather are dense enough to deflect or break a light needle. Sequins are hard plastic sitting right on the seam line.
  • The fabric grips the machine. Vinyl and leather stick to metal presser feet and stop feeding.

Each fix is a small change to the needle, stitch, thread, presser foot or how you handle the fabric. For knits, which is where most people start, you usually need all four of the setup changes below.

The four-part setup for stretch fabric

Needle

Change the needle first. A universal needle can pierce or snag knit loops, and it’s a very common cause of skipped stitches on stretch fabric. Use:

  • a jersey (ballpoint) needle for cotton jersey, interlock, rib and sweater knits;
  • a stretch needle for fabrics with a lot of spandex/elastane, such as swimwear, leggings fabric and power mesh.

Sizes 70/10 to 80/12 suit lightweight knits, and 90/14 suits heavier knits like sweatshirt fleece. Our answer to which needle to use for stretchy fabric explains the difference between the two point types, and the needle sizes and types chart covers every other fabric.

Stitch

A plain straight stitch has almost no give, so it tends to snap when a knit seam is stretched. Use a stitch that can lengthen with the fabric:

  • Narrow zigzag: available on nearly every machine. A width of about 1–1.5 mm and a length of about 2.5 mm is a reasonable starting point for seams.
  • Lightning bolt / stretch straight stitch: looks almost straight from the outside but has a slight zigzag built in.
  • Triple straight stitch: very strong, useful for stress points, but slow to sew and hard to unpick.
  • Three-step (multi-step) zigzag: lies flatter than a regular zigzag and is good for attaching elastic and finishing edges.
  • Overlock-style stitches: seam and overcast the edge in one pass.

Stitch names and symbols vary by brand. Tension settings and stretch stitches for knit fabric goes through each one, with notes on finding them on machines like the Singer Heavy Duty.

Thread

Use a good-quality all-purpose polyester thread. Polyester has a little natural give, while 100% cotton thread is more likely to break when the seam stretches. Specialist stretch threads such as woolly nylon or elastane-blend threads can add extra give for swimwear and activewear. See what kind of thread to use for stretch fabric for when they’re worth using.

Presser foot pressure and feeding

If your machine has a presser foot pressure dial, try lowering it. Heavy pressure squeezes the top layer of a knit forward while the feed dogs pull the bottom layer through, and you end up with a wavy, “lettuce-edged” seam that you didn’t want. A walking foot or a built-in dual-feed system (such as Pfaff’s IDT) helps for the same reason: it feeds the top layer at the same rate as the bottom one.

Just as important: don’t pull the fabric. Support its weight so it doesn’t drag off the table, and let the feed dogs move it.

Step-by-step: sewing a knit seam on a regular machine

  1. Prewash the fabric if the finished item will be washed, because many knits shrink.
  2. Fit the right needle (jersey or stretch, sized to the fabric weight).
  3. Thread with polyester in both the top and the bobbin.
  4. Choose the stitch. Start with a narrow zigzag or your machine’s stretch stitch.
  5. Lower the presser foot pressure a little if you can.
  6. Test on a scrap of the same fabric, with the same number of layers, cut in the same direction. Stretch the test seam firmly. If threads pop, add width or change to a stretchier stitch. If the seam ripples, reduce the foot pressure or try a walking foot.
  7. Pin or clip within the seam allowance, using fine ballpoint pins or clips.
  8. Start carefully. Knits can get pushed down into the needle plate hole. Hold the thread tails as you start, or start on a small scrap of tear-away stabilizer.
  9. Sew at an even, moderate speed without stretching the fabric, unless the pattern tells you to (for example, when easing in a neckband).
  10. Press gently with a press cloth and a temperature suited to the fibre. Many activewear knits are synthetic and can be damaged by a hot iron.

Hemming knits without a coverstitch machine

Ready-to-wear T-shirts are usually hemmed with a coverstitch, which looks like two parallel rows on the outside and a looped thread on the inside. On a regular machine you can get close with:

  • A twin needle (stretch or jersey twin) with a straight stitch. The single bobbin thread zigzags between the two needle threads on the underside, which gives the hem some stretch. Check that your machine accepts twin needles and that the needle plate opening is wide enough.
  • A narrow zigzag or stretch stitch for a sporty or casual finish.
  • A lettuce hem, a deliberately rippled edge made with a dense zigzag. Our tutorial on how to sew a lettuce hem covers settings and technique.

Lightweight fusible knit interfacing or a strip of wash-away stabilizer in the hem allowance can stop the hem from tunnelling or stretching out.

Common stretch-sewing problems and fixes

Problem Likely causes Things to try
Skipped stitches Wrong needle type, dull or damaged needle, needle too small or too large New jersey or stretch needle; try a different size; rethread
Seams pop when stretched Straight stitch on a stretchy fabric; cotton thread Narrow zigzag or stretch stitch; polyester thread
Wavy or rippled seam Too much presser foot pressure; fabric stretched while sewing Lower foot pressure; walking foot; don’t pull; stabilize the seam
Fabric pushed into the needle plate Fine knit, starting right at the edge Hold thread tails; start on stabilizer; use a straight-stitch plate for straight stitches only
Ridge or “tunnel” between twin-needle rows Upper tension too high for the fabric; no stabilizer Lower upper tension slightly; lengthen the stitch; add stabilizer to the hem
Holes or runs along the seam Needle point cutting the knit loops Switch to a ballpoint or stretch needle; use a finer size

What is the best sewing machine for stretch fabrics?

No single model is “best” for everyone, and you don’t need a specialist machine to sew knits well. With the right needle, stitch and handling, a basic mechanical machine with a zigzag can sew T-shirts, leggings and loungewear. Some features do make stretch sewing noticeably easier, though.

Features that matter

  • Adjustable presser foot pressure. This is one of the most useful features for knits, and many basic machines leave it out.
  • Built-in stretch stitches such as lightning bolt, triple straight, three-step zigzag and an overlock-style stitch.
  • Dual feed or walking foot compatibility. Some brands build this in (Pfaff’s IDT system is the best-known example). On other machines you buy a walking foot separately; check that one is available for your model.
  • Twin needle capability for hems.
  • A free arm for sewing cuffs, sleeve hems and small leg openings.
  • Speed control and needle up/down, which make slow, controlled sewing easier on slippery knits.

Do you need a serger or coverstitch machine?

A serger (overlocker) trims, seams and finishes the edge in one pass, and uses differential feed to stop knits stretching out or puckering. If you sew a lot of knit garments, it’s the single biggest upgrade. It doesn’t replace a regular machine, though. You’ll still need one for topstitching, buttonholes, zips and appliqué.

A coverstitch machine mainly sews professional-looking hems and bindings on knits. It’s a nice extra for people who sew a lot of T-shirts and activewear, but a twin needle on a regular machine is a reasonable substitute for most home sewists.

If you’re choosing a single machine for knits, try it in a shop with your own fabric if you can. Check how it feeds two layers of lightweight jersey, whether you can lower the foot pressure, and how its stretch stitches look when you pull the seam.

Other tricky fabrics, and where to start with each

Knits aren’t the only fabrics that need a different setup. These cluster guides go into detail:

General habits that help with any difficult fabric

  • Start every awkward project with a new needle of the right type.
  • Always sew a test seam on a scrap with the same layers and grain direction.
  • Slow down. Turn the handwheel by hand over thick spots, sequins or seam intersections.
  • Use clips rather than pins on anything that keeps holes (leather, vinyl, laminated fabrics) and on thick layers.
  • Clean out lint afterwards. Pile fabrics, felt and fleece shed a lot of fibre into the bobbin area.
  • Read your machine’s manual for its recommended needle range and maximum fabric thickness, and stay within them.

Keep exploring

Guides from other topics

All topics →