Sewing Basics

How to Thread a Sewing Machine (With Diagram)

Step-by-step guide to threading a sewing machine, with a threading diagram, Singer beginner tips, bobbin thread pickup and how to spot a threading mistake.

On this page
  1. Before You Start
  2. Threading Diagram
  3. Step-by-Step: Upper Threading
  4. Using the Built-In Needle Threader
  5. Threading a Singer Sewing Machine (Beginner Notes)
  6. How to Thread the Bottom Thread (Bobbin)
  7. Bringing Up the Bobbin Thread
  8. Should You Thread With the Foot Up or Down?
  9. What Is a 90/14 Needle Used For?
  10. Signs Your Machine Is Threaded Wrong

Threading is the first thing you’ll do on a sewing machine, and it causes more problems than anything else when it’s slightly off. The good news is that the thread path is very similar on almost every home machine. This guide gives you a general diagram, the steps in order, and the checks that catch most mistakes. Your manual’s diagram, or the numbers printed on your machine, will show the exact path for your model.

Before You Start

  • Switch the machine on so the light helps you see. For extra safety, some people switch it off before threading the needle by hand. Either way, keep your foot off the pedal.
  • Raise the presser foot.
  • Raise the needle to its highest position by turning the handwheel toward you. On many machines the take-up lever is also at its highest point when the needle is. On computerised machines, a needle up/down button may do this for you.
  • Have a wound bobbin ready. See how to wind and insert a bobbin.

Threading Diagram

This is the general upper thread path found on most modern home machines:

   [Spool pin] ──► (1) Top thread guide
                         │
                         ▼
               (2) Down the right-hand channel
                   ── passes between the tension discs ──
                         │
                         ▼
               (3) U-turn at the bottom
                         │
                         ▼
               (4) Up the left-hand channel
                         │
                         ▼
               (5) Take-up lever (thread through its eye or hook, right to left)
                         │
                         ▼
               (6) Back down the left channel
                         │
                         ▼
               (7) Guide just above the needle (on the needle bar)
                         │
                         ▼
               (8) Needle eye — front to back on most modern machines

Older and vintage machines may route the thread differently. For example, some have the tension discs on the front of the machine, and some thread the needle from left to right or right to left. Follow your manual if your machine doesn’t match.

Step-by-Step: Upper Threading

  1. Put the spool on the spool pin. On a horizontal pin, add a spool cap a little larger than the end of the spool so the thread comes off smoothly. On a vertical pin, a felt pad underneath helps.
  2. Pull the thread through the top guide, usually a small hook or slot on the top of the machine.
  3. Bring the thread down the right-hand channel. Hold the thread lightly near the spool with one hand and guide it with the other, so it slips firmly between the tension discs. You may feel a slight resistance.
  4. Go around the U-turn at the bottom and back up the left-hand channel.
  5. Catch the take-up lever. Pass the thread through the eye or slot of the take-up lever, usually from right to left. If you can’t see the lever, turn the handwheel toward you until it rises.
  6. Bring the thread back down the left-hand channel.
  7. Slip the thread behind the guide above the needle. This is usually a small wire or hook on the needle bar or the needle clamp.
  8. Thread the needle (most modern machines thread front to back) and pull through a tail of about 10–15 cm (4–6 inches). Draw it under the presser foot toward the back.

Using the Built-In Needle Threader

Many machines have a lever on the left of the needle area that pushes a tiny hook through the needle eye. The usual steps are:

  1. Raise the needle to its highest position. Many manuals recommend a centre needle position and a straight stitch.
  2. Lower the threader lever and guide the thread around its guide hooks as your manual shows.
  3. Pass the thread in front of the tiny hook and across.
  4. Release the lever slowly. A loop of thread is pulled through the eye, and you pull the loop through to the back.

Singer’s own guidance notes that very heavy thread can’t be pulled through a fine needle this way, and that you shouldn’t lower the threading lever while the machine is running. If the threader won’t work with your thread or needle, thread the needle by hand. For more help, see how to thread a sewing machine needle with poor eyesight.

Threading a Singer Sewing Machine (Beginner Notes)

Most current Singer home machines follow the same diagram above, and many have numbered guides printed on the body. A few Singer-specific points beginners often ask about:

  • Raise the presser foot first. Singer’s own threading guide stresses this.
  • Use the spool cap that most closely matches the size of the spool.
  • Make sure the thread really sits in the take-up lever. This is the step most often missed.
  • Needle direction: most modern Singer models thread front to back. Some vintage Singers thread differently, so check the manual for your model number. Many Singer manuals can be found on Singer’s support site.

The same applies to Brother, Janome and other brands: the order of guides is very similar, and the printed numbers on the machine show the exact path.

How to Thread the Bottom Thread (Bobbin)

The “bottom string” is the bobbin thread. In brief:

  • Drop-in bobbin: remove the clear cover, drop in the bobbin so it turns in the direction shown on the diagram near the bobbin area (often counterclockwise), guide the thread through the slot until it clicks under the tension spring, and replace the cover.
  • Front-loading bobbin: put the bobbin in its metal case, pull the thread through the slot and under the tension spring, and click the case into the machine with the latch open.

Our full guide on how to wind and insert a bobbin covers both in detail.

Bringing Up the Bobbin Thread

Many newer drop-in machines don’t need this step. You can leave the bobbin thread tail under the cover, and it catches on the first stitch. If yours needs it:

  1. Hold the upper thread tail loosely in your left hand.
  2. Turn the handwheel toward you one full turn so the needle goes down and comes back up.
  3. Pull the upper thread gently. A loop of bobbin thread comes up through the needle plate.
  4. Pull the loop to free the end, then draw both tails under the foot and toward the back.

Should You Thread With the Foot Up or Down?

Up. Raising the presser foot opens the tension discs. If you thread with the foot down, the discs are closed and the thread can sit on top of them instead of between them. Then the upper thread has almost no tension, which typically shows up as loops or a tangle on the underside of the fabric. Lower the foot only when you’re ready to sew.

What Is a 90/14 Needle Used For?

A 90/14 needle is a medium-to-medium-heavy size. With a universal point, it’s a common choice for mid-weight fabrics like heavier cotton, linen, light denim and some home decor fabrics. An 80/12 is often used for lighter quilting cotton and shirting, and 100/16 for heavier denim or canvas. The thread should pass easily through the needle eye, so heavier threads need larger needles. To swap sizes, see how to change a sewing machine needle, and for the full range of sizes and types, our needle chart.

Signs Your Machine Is Threaded Wrong

Symptom Likely threading cause
Loops or a “bird’s nest” under the fabric Upper thread missed the tension discs (often threaded with the foot down) or missed the take-up lever
Thread comes out of the needle on the first stitch Tail too short, or the take-up lever wasn’t at its highest point when you started
Upper thread keeps breaking Thread caught on the spool notch, spool cap missing, or a guide skipped
Bobbin thread pulled up in loops on top Bobbin thread not in its tension slot
No stitches forming Needle threaded from the wrong side, or the needle inserted backwards

When in doubt, remove the upper thread completely and rethread from the spool with the presser foot up. If problems continue, check the needle and the bobbin, or work through our sewing machine troubleshooting guide. Our complete guide to using a sewing machine covers test seams and tension.

The complete guide to sewing basics

How to Use a Sewing Machine: A Complete Beginner's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →