Sewing Machine Troubleshooting

Why Your Sewing Machine Isn't Feeding Fabric (and How to Fix the Feed Dogs)

Fabric not moving under the needle? Check the feed dogs, presser foot, stitch length and lint first. Here's how to diagnose and fix sewing machine feeding.

On this page
  1. Quick Checks First
  2. How Feeding Works
  3. Check the Feed Dogs Are Up and Moving
  4. Common Causes
  5. Fabric Feeds Unevenly or Only in Reverse
  6. When It’s Mechanical

Quick Checks First

If the needle is moving but the fabric isn’t, check these before anything else. They take seconds and cover the most common causes:

  1. Is the presser foot down? The feed dogs need the foot pressing the fabric onto them.
  2. Are the feed dogs raised? Look for a drop-feed lever or button, often at the back or side of the free arm, or a setting on computerised machines.
  3. Is the stitch length above zero? At 0, the feed dogs don’t move the fabric forward.
  4. Is a cover plate fitted? A darning plate placed over the feed dogs stops them gripping.
  5. Is the machine in free-motion or darning mode? Some computerised machines lower the feed dogs or stop feeding in these modes.

If the machine passes these checks, read on.

How Feeding Works

Under the presser foot, the feed dogs are small rows of metal teeth that rise through slots in the needle plate. On each stitch, they come up, grip the underside of the fabric against the presser foot, move it backwards a stitch length, then drop down and return. The presser foot provides the pressure that lets them grip. If any part of this — the teeth rising, the foot pressing, or the movement itself — is missing, the fabric stays put.

Check the Feed Dogs Are Up and Moving

  1. Raise the presser foot and remove the fabric.
  2. Turn the handwheel slowly toward you and watch the feed dogs.
  3. You should see them rise above the needle plate, move toward the back of the machine, drop below the plate, and return to the front.

If they stay below the plate, they’re lowered, so check the drop-feed control. If they rise but don’t move backwards, check the stitch length. If they barely rise, or don’t move at all with everything set correctly, there may be a mechanical problem.

Common Causes

Feed dogs lowered or covered

Feed dogs are lowered for free-motion quilting, darning and sewing on buttons. It’s easy to forget to raise them again. On many machines, after you raise the control, the feed dogs pop back up on the next turn of the handwheel or the first stitch. On older machines without a drop-feed control, a separate cover plate may be clipped over them.

Presser foot up or pressure too low

If the presser foot is up, there’s nothing to press the fabric onto the feed dogs. Machines with an adjustable presser foot pressure dial can also be set so low that the fabric slips. Return the pressure to the normal setting in your manual and test. Very slippery or very thick fabrics may need small pressure adjustments.

Stitch length set to zero

A stitch length of 0 is used for bar tacks and sewing on buttons, but it means the fabric doesn’t move. Turn the length up to a normal setting, often around 2.5 mm for general sewing.

Lint packed in the feed dogs

Lint can pack between and under the feed dog teeth so tightly that they can’t rise properly or grip. Unplug the machine, remove the needle plate and brush out between the teeth and the slots. Small tweezers help with compacted lint. You may be surprised how much is there, especially after sewing fleece, flannel or batting.

Thread jam underneath

A tangle of thread under the needle plate can hold the fabric down and stop it moving even when the feed dogs work. If you see a bird’s nest on the underside, or the fabric feels anchored, clear the jam. See how to fix thread bunching underneath and clearing sewing machine jams.

Needle problems

A blunt or bent needle can drag on the fabric instead of piercing it cleanly, holding it back on each stitch. Fit a new needle of the right type and size for the fabric.

Fabric being pushed into the plate

If the start of the seam gets pulled down into the needle hole instead of feeding, the fabric is usually too fine for the wide zigzag plate opening, or you started too close to the edge. Start a few millimetres in, hold the thread tails for the first stitches, use a fresh fine needle, and consider a straight-stitch plate for straight seams if your machine has one. Our main troubleshooting guide has more on freeing stuck fabric.

Thick seams and the wrong foot

Some feet, such as a satin stitch foot, have a narrow channel underneath and can catch on thick layers. When climbing onto a thick seam, the foot can also tilt so the feed dogs lose grip. Use a general-purpose foot or a walking foot for bulky work, and level the foot with a folded scrap behind the seam. See how to sew through thick fabric.

Fabric Feeds Unevenly or Only in Reverse

Layers creeping. The feed dogs move the bottom layer, while the presser foot can slow the top one. Over a long seam, the top layer can end up longer, causing puckers or mismatched ends. A walking foot or built-in dual feed helps. So does pinning or clipping at regular intervals, and slightly reducing presser foot pressure. Our guide to stopping seams puckering covers this in more detail.

Fabric pulling to one side. A presser foot that is loose or bent, or uneven lint in the feed dogs, can steer the fabric sideways. Check the foot sits flat and is firmly attached, and clean the feed dogs.

Feeding only in reverse, or not reversing. If the machine feeds forward but not in reverse, or the reverse lever has stuck down, the reverse mechanism may be sticking or damaged. On older mechanical machines it is sometimes due to stiff, dried oil. On any machine, if gentle operation of the lever doesn’t free it, have it checked. If the machine sews backwards when it should go forwards, see why a machine stitches backwards.

Shorter stitches than set. If stitches come out shorter than the length setting, check for drag. The fabric may be catching on the table edge, hanging heavily off the side, or held back by the foot. Support the weight of large projects so the machine isn’t pulling it.

When It’s Mechanical

If the feed dogs don’t move when you turn the handwheel with the length set correctly and feed dogs raised, or they move only weakly, the feed mechanism may need adjusting or repair. Feed dog height and feed timing can be adjusted on many machines, but these are generally technician jobs that need the service manual. A professional service, as described in how often to service your sewing machine, usually includes checking the feed system.

The complete guide to sewing machine troubleshooting

Sewing Machine Troubleshooting: Fixing Common Stitch Problems
Read the guide

Keep exploring

Guides from other topics

All topics →