Machine Embroidery

How to Use an Embroidery Machine: A Beginner's Guide

Learn to use an embroidery machine step by step: supplies, threading, loading designs, stabilizing, hooping, stitching, finishing, and beginner tips.

On this page
  1. What an embroidery machine actually does
  2. What you need before your first stitch-out
  3. Step 1: Set the machine up for embroidery
  4. Step 2: Thread the top and load the bobbin
  5. Step 3: Choose and load a design
  6. Step 4: Stabilize and hoop the fabric
  7. Step 5: Attach the hoop and position the design
  8. Step 6: Stitch the design and handle color changes
  9. Step 7: Unhoop and finish
  10. Good first projects (and ones to save for later)
  11. Is it hard to use an embroidery machine as a beginner?
  12. Tips and tricks that save the most frustration
  13. When something goes wrong
  14. What makes an embroidery machine easy to use?

What an embroidery machine actually does

On a sewing machine, you steer the fabric while the feed dogs move it forward. An embroidery machine works differently. Your fabric is clamped in a hoop, the hoop locks onto a motorized arm (the carriage), and the machine moves the hoop under the needle by following a digital design file. You don’t guide anything while it stitches. Your part comes before and after: picking the design, preparing the fabric, threading, and finishing.

Home embroidery machines come in three broad types:

  • Embroidery-only single-needle machines, which stitch designs but can’t sew seams.
  • Sewing and embroidery combination machines, which sew normally and accept a detachable embroidery unit.
  • Multi-needle machines, which hold several thread colors at once and switch between them automatically. These are popular with small businesses.

If you’re still deciding which kind you need, our comparison of sewing machines and embroidery machines explains the trade-offs.

What you need before your first stitch-out

The machine is the big purchase, but the consumables decide whether your stitch-outs look good. Here is a basic starter kit:

Item What to get Why it matters
Hoop(s) The hoop(s) that came with your machine Holds fabric still while the carriage moves
Designs Built-in designs, or files in your machine’s format The machine can only stitch files it can read
Top thread 40 weight polyester or rayon embroidery thread Standard weight most designs are digitized for
Bobbin thread Lightweight embroidery bobbin thread (often 60 or 90 weight), white or black Keeps the back flat and helps tension balance
Needles 75/11 embroidery needles; 75/11 ballpoint for knits Embroidery needles are built for dense, fast stitching
Stabilizer A medium cutaway and a medium tearaway to start Supports the fabric so stitches don’t pucker or distort
Small tools Curved embroidery scissors, a removable marking pen, a USB stick For trimming, placement, and transferring files

Optional extras worth having early include temporary spray adhesive, a water-soluble topper for towels and fleece, and a lint brush.

Two supply decisions confuse beginners most: which stabilizer to use for each fabric and which thread brand to buy. Both have their own guides.

Step 1: Set the machine up for embroidery

On an embroidery-only machine, the embroidery arm is usually built in or already attached, so you can skip ahead.

On a combination machine:

  1. Turn the machine off. Most manuals say to attach or remove the embroidery unit with the power off.
  2. Remove the flatbed extension or accessory tray, then slide the embroidery unit onto the free arm until it clicks into its connector.
  3. Clear space behind and beside the machine. When you power on, the carriage usually moves through a calibration routine, and it needs room to travel without hitting a wall or a stack of fabric.
  4. Swap to the embroidery foot. Combination machines use a specific embroidery foot that hovers just above the fabric. Your manual will name it.
  5. Insert a fresh embroidery needle, flat side of the shank toward the back on most home machines, pushed all the way up before you tighten the clamp.

Some machines lower the feed dogs automatically in embroidery mode and some ask you to do it. Check your manual.

Step 2: Thread the top and load the bobbin

Thread the top with the presser foot raised. Raising the foot opens the tension discs so the thread can seat between them. If you thread with the foot down, the thread skips the tension, and you’ll usually get a tangled nest under the fabric within seconds. Follow your machine’s numbered thread path, making sure the thread passes through the take-up lever, then use the needle threader if you have one.

For the bobbin, use embroidery bobbin thread rather than your top embroidery thread. A lighter bobbin thread takes up less space under dense stitching and makes it easier for the top thread to pull the interlock to the back, where it belongs. Insert the bobbin so it unwinds in the direction your manual shows, and draw the thread through the tension slot or under the spring until it seats.

Some machines come with a second bobbin case meant for embroidery or for certain bobbin threads. If yours did, the manual will say when to use it.

Step 3: Choose and load a design

Start with a built-in design for your first stitch-out. It’s already digitized for your machine and sized for your hoops, so you can be fairly sure it will stitch well.

When you’re ready for outside designs, download the file in your machine’s native format. Brother and Baby Lock use PES, Janome uses JEF, and Husqvarna Viking and Pfaff use VP3, among others. Our guide to embroidery file formats has the full list and explains what to do when a file won’t show up on your machine. A JPG or PNG picture is not an embroidery file. Images have to be digitized into stitches first.

Transfer the file by USB stick, cable or wireless app, depending on your machine. Then check three things on screen:

  • The design fits the hoop you plan to use. Most machines warn you if it doesn’t.
  • The size is close to the original. Many experienced embroiderers suggest resizing stitch files by no more than about 10–20 percent on the machine. Shrinking a design a lot packs stitches too densely, and enlarging it a lot leaves gaps.
  • The color sequence. Note how many thread changes the design needs so you can line up your spools.

Step 4: Stabilize and hoop the fabric

Stabilizer is the backing (and sometimes a top layer) that keeps fabric from stretching or puckering under thousands of needle penetrations. A quick rule of thumb:

  • Stretchy fabrics (T-shirts, sweatshirts, knits) get cutaway, which stays in the garment permanently.
  • Stable woven fabrics (quilting cotton, denim, canvas) usually get tearaway.
  • Textured fabrics (towels, fleece, velvet) also get a water-soluble topper so stitches don’t sink into the pile.

Cut the stabilizer larger than the hoop on all sides. Put the outer ring on a flat, hard surface, lay the stabilizer and fabric over it, and press the inner ring in evenly. The fabric should be smooth and firm, but not stretched. Pulling the fabric tight like a drum skin distorts the weave, and it springs back when you unhoop, which creates puckers. Our full guide to hooping fabric without puckers or hoop burn covers floating, magnetic hoops and tricky items.

Step 5: Attach the hoop and position the design

Slide the hoop onto the carriage until it locks. Most machines confirm this with a click or an on-screen message.

Then position the design:

  • Use the trace or trial function if your machine has one. The carriage traces the design’s outer boundary so you can confirm it stays clear of the hoop frame and lands where you want it.
  • Move the design on screen to line the needle up with the center mark or crosshairs you drew on the fabric.
  • Check under the hoop. With garments, bags and pillow covers, make sure the back layer isn’t bunched under the hoop, where it would get stitched to the front.

Step 6: Stitch the design and handle color changes

Lower the embroidery foot if your machine needs it, then press start. Hold the top thread tail lightly for the first few stitches if your manual suggests it. This keeps the tail from being pulled underneath.

Stay with the machine for the first color. Most problems, like a nest forming underneath, the thread shredding, or the fabric lifting with the needle (called “flagging”), show up in the first minute. If you hear a change in sound or see thread looping on top, stop the machine and check before it gets worse.

When one color finishes, single-needle machines stop and show the next color. Rethread with the presser foot up, trim the tail if your machine doesn’t do it automatically, and press start again. Multi-needle machines change colors on their own once you’ve assigned spools to needles.

Many machines let you reduce speed. Slow down for metallic threads, dense designs, small lettering, or any time thread keeps breaking.

Step 7: Unhoop and finish

When the design is done:

  1. Remove the hoop from the machine, then release the fabric from the hoop.
  2. Trim jump stitches, the threads that travel between parts of the design, close to the surface on the front and back.
  3. Remove the stabilizer. Tear tearaway gently, holding the stitches with your other hand so they don’t distort. Trim cutaway with scissors, leaving a margin of roughly 1/4 to 1/2 inch around the design and rounding the corners. Cut away excess wash-away and rinse out the rest following the product’s instructions.
  4. Press from the back with the embroidery face down on a folded towel, so the stitches keep their raised texture instead of being flattened.

Good first projects (and ones to save for later)

These usually go well for beginners:

  • Flour-sack or cotton tea towels. The fabric is stable and woven, it works with tearaway, and it’s inexpensive.
  • Canvas tote bags. They’re sturdy and forgiving. Choose a tote with a flat panel that fits your hoop.
  • Quilt blocks and fabric patches. These are flat pieces with no garment to work around.
  • Felt. It doesn’t fray and holds stitches well.

Save these for your second or third week:

  • T-shirts and other knits. They stretch, so they need cutaway, careful hooping and lighter designs. When you’re ready, follow our guide to machine embroidering a T-shirt without stretching or puckering.
  • Terry towels. They need a topper or stitches disappear into the loops.
  • Caps, leather, vinyl and velvet. Each needs special handling or hoops.

Is it hard to use an embroidery machine as a beginner?

Pressing start isn’t hard. The machine does the stitching, and the touchscreens on most current models walk you through threading and color changes. The learning curve is in the preparation: choosing the right stabilizer, hooping without distorting the fabric, and recognizing a thread or tension problem before it ruins a project. Most beginners get a clean stitch-out on stable cotton within their first few sessions. Knits, towels and dense designs take longer to get right.

Starting with built-in designs and stable woven fabrics, and adding one new variable at a time, is the most reliable way to build confidence.

Tips and tricks that save the most frustration

  • Test-stitch on a scrap of the same fabric with the same stabilizer. This is the single most useful habit in machine embroidery, especially for a new design or fabric.
  • Change the needle often. Common guidance is a new needle per project or roughly every eight hours of stitching, and immediately after any needle strike or nest.
  • Clean the bobbin area regularly. Embroidery produces a lot of lint. Brush out the bobbin case and race following your manual. Oil only if and where your manual says.
  • Keep a notebook. Record the fabric, stabilizer, needle, thread and any tension change for projects that came out well.
  • Buy designs from reputable digitizers. A poorly digitized file can cause puckering, thread breaks and gaps that no machine setting will fix.
  • Never pull fabric after the hoop is tightened. Straighten it by re-hooping instead.
  • Use the right thread path for your spool. Stack-wound spools usually sit upright, while cross-wound spools are often designed to feed from the end. If thread keeps twisting or catching, try a separate thread stand.

When something goes wrong

Most problems trace back to a short list of causes: threading, the needle, the bobbin, stabilizer and hooping, or the design file. These guides cover the common failures:

What makes an embroidery machine easy to use?

No single machine is the easiest for everyone, but these features generally make the learning curve gentler:

  • A clear color touchscreen for moving, rotating and resizing designs, and for seeing the color sequence.
  • An automatic needle threader and thread trimmer.
  • A hoop size that matches your projects. A 4 x 4 inch (about 100 x 100 mm) field is fine for monograms and small motifs. A 5 x 7 inch (about 130 x 180 mm) field or larger opens up far more designs.
  • Easy design transfer by USB or wireless.
  • Local dealer support or classes, which can matter more than any feature for a beginner.

For a brand-by-brand overview, see which brand makes the best embroidery machine. If you’re thinking about selling what you make, read whether owning an embroidery machine can be profitable before upgrading. And if you already own a cutting machine, here’s what a Cricut can and can’t do for embroidery.

Keep exploring

Guides from other topics

All topics →