What to Do the Moment It Jams
When a sewing machine jams, the needle stops, the handwheel goes stiff, and there is often a knot of thread under the fabric. Stop pressing the foot pedal immediately. Running the motor against a jam winds the thread tighter around the hook, and can bend the needle or strain the drive.
Don’t pull the fabric hard to free it. Most jams can be cleared in a few minutes with small scissors, tweezers and patience.
How to Clear a Thread Jam Step by Step
- Switch off and unplug the machine.
- Raise the presser foot. This releases pressure on the fabric and opens the upper tension.
- Try turning the handwheel gently toward you. If it moves, bring the needle to its highest position. Sometimes this alone releases a loop caught in the hook. If it won’t move with gentle pressure, stop. Don’t force it.
- Cut the top thread above the needle, then snip the tangled threads under the fabric, between the fabric and the needle plate. Lift the fabric away once it is free.
- Remove the needle plate (most come off with one or two screws or a release button; check your manual) and take out the bobbin and bobbin case.
- Pick out all the trapped thread. Use tweezers to pull scraps from around the hook, feed dogs and bobbin holder. Look for small pieces wrapped around the hook. They are easy to miss.
- Brush out lint while you are there.
- Check the needle for bends or a blunt point, and replace it if in doubt.
- Reassemble and rethread the top with the presser foot raised, and reinsert the bobbin correctly.
- Turn the handwheel by hand through a few full turns to check it moves freely before sewing again.
When the Needle Is Stuck Down
A needle stuck in the down position is almost always held by thread wrapped around the hook below the plate, or by a broken needle tip or pin wedged there.
- Unplug the machine.
- Cut the top thread just above the needle eye to remove the strain from above.
- Rock the handwheel very gently back and forth by a small amount. Often this loosens the thread enough to free it. Use only light pressure.
- Remove the needle plate if you can get to its screws, and the bobbin case. Cut and pull out the thread jammed around the hook.
- Look for a broken needle tip or pin in the bobbin area and remove it with tweezers.
- Once the wheel turns freely, bring the needle up and check it is undamaged.
Getting the needle out
If the wheel still won’t turn, you can often loosen the needle clamp screw and slide the needle down and out, which may give you better access to clear the jam. Hold the needle as you loosen the screw so it doesn’t drop into the machine. If the needle is wedged, small pliers can help, but use gentle force.
Some machines have a hook retainer or “race cover” that can be opened to expose the hook. Only remove parts your manual describes. If you can’t free the mechanism without forcing it, take it to a technician. Forcing a locked machine can knock the hook timing out of adjustment.
Why It Jams After a Few Stitches
A machine that sews two or three stitches and then locks up usually has a setup problem, not a mechanical fault:
- Threaded with the presser foot down. The thread misses the tension discs and loops uncontrollably under the fabric. Rethread with the foot up.
- Missed take-up lever. Without the lever, the slack from each stitch is never pulled back up. Check the thread passes through it.
- Bobbin in the wrong way, or the wrong type. Check the direction in your manual and use the bobbin class or size it specifies. Bobbins are not universal.
- Loose thread tails. Hold both tails behind the foot for the first few stitches.
- Starting right on the edge of fine fabric, so it is pushed into the plate hole. Start a few millimetres in, or on a scrap.
- A damaged needle that fails to form a loop for the hook.
These overlap closely with bird’s nesting. See how to fix thread bunching underneath for more detail.
Bobbin Jams
If the jam always seems to start in the bobbin area:
- Rewind the bobbin. Loose or uneven winding can spill thread that catches on the hook.
- Check the bobbin is the right type. Plastic and metal bobbins, and different classes, are not interchangeable on many machines.
- Seat the bobbin case properly. On many machines with a drop-in bobbin, the plastic case has a tab or notch that must sit in its slot. If it’s not seated, it can shift and catch the needle or thread. On front-loading machines, the bobbin case should click home.
- Clean out lint, which can pack in behind the case and stop it seating.
- Look for burrs on the bobbin case where the needle may have struck it. A damaged case can snag thread repeatedly and may need replacing.
Turning the Handwheel the Wrong Way
On most home machines, the handwheel should be turned toward you (counter-clockwise when viewed from the right-hand end). Turning it away from you, backwards, works against the way the hook is designed to pick up and release the thread loop. On many machines this can pull the top thread down and wrap it around the hook, causing a jam. A small reverse movement while rocking free a jam is usually fine. Turning it backwards repeatedly while threaded is a common cause of tangles. Check your manual if you are unsure which way is correct for your machine.
A Machine That Has Seized Up
A machine that has been stored for a long time may be stiff or completely locked even with no thread in it. A common cause on older mechanical machines is old oil that has thickened and gone gummy, sometimes combined with dust and lint.
For a machine you are allowed to oil yourself (your manual will show oiling points if so):
- Unplug it and remove thread, needle, bobbin and the needle plate.
- Clean away lint and dust.
- Apply a drop of sewing machine oil at each oiling point shown in the manual. Use only oil sold for sewing machines, not household or cooking oil.
- Leave it for a while for the oil to soften old residue, then try turning the handwheel gently by hand, a little at a time.
Many modern machines are designed not to need oiling by the owner, or only in specific places. Don’t add oil to a machine whose manual doesn’t call for it. If a seized machine doesn’t loosen with gentle effort, or if it is computerised, have it serviced rather than forcing it. For an older all-metal machine, our guide to cleaning and oiling a vintage sewing machine goes into more detail.
How Do You Disengage the Needle?
If you want the needle to stay still, for example to wind a bobbin, many mechanical machines have an inner knob (sometimes called a clutch or stop-motion knob) in the centre of the handwheel. Loosening it lets the wheel turn without moving the needle. Many modern machines instead stop the needle automatically when the bobbin winder is pushed into winding position. If your needle unexpectedly won’t move while the motor runs, see motor runs but the needle won’t move.
Preventing Repeat Jams
- Thread with the presser foot up, and check the take-up lever.
- Start and stop with the needle at its highest point.
- Hold the thread tails for the first few stitches.
- Use the correct bobbin type and wind it evenly.
- Clean lint out of the bobbin area regularly, especially after fleece, flannel or batting.
- Remove pins before they reach the presser foot.
- Change needles regularly.
When to Stop and Get Help
Take the machine to a technician if:
- the handwheel still won’t turn after clearing every visible thread
- it turns but feels rough, or catches at the same point in every rotation
- after a hard jam, it skips stitches or the needle strikes the hook or plate (the timing may have been knocked out; see our timing guide)
- a computerised machine shows an error that clearing the jam doesn’t reset
For more stitch problems by symptom, see the main troubleshooting guide.