Sewing Machine Troubleshooting

How to Stop Seams Puckering on a Sewing Machine

Seams puckering? Find the cause with a simple stitch test, then fix it by adjusting tension, stitch length, needle, thread, presser foot and fabric handling.

On this page
  1. Why Seams Pucker
  2. Find the Type of Pucker First
  3. Fix 1: Lighten and Balance the Tension
  4. Fix 2: Adjust the Stitch Length
  5. Fix 3: Use a Finer Needle and Thread
  6. Fix 4: Control How the Layers Feed
  7. Fix 5: Support Fine Fabric
  8. Fix 6: Handle the Fabric Gently
  9. Puckering After Washing
  10. Press to Set the Seam
  11. Knits: Puckered or Wavy?
  12. Quick Checklist

Why Seams Pucker

A puckered seam has small ripples or gathers along the stitching instead of lying flat. It’s most common on fine, tightly woven or slippery fabrics such as cotton lawn, poplin, silk, satin and polyester. It’s rarer on heavier, looser fabrics.

There’s usually more than one cause, but they fall into four groups:

  • Tension. The thread is stretched as it’s sewn, then relaxes and draws the fabric up.
  • Thread or needle too big for the fabric. In a dense weave, there isn’t room for the thread without pushing the fabric’s yarns aside. This is sometimes called structural jamming.
  • Uneven feeding. One layer feeds faster than the other, and the stitches lock the difference in.
  • Shrinkage. The thread and fabric shrink by different amounts when washed.

Find the Type of Pucker First

A simple test shows which cause you’re dealing with. Sew a test seam on two layers of your project fabric, using your normal settings, then:

  1. Carefully snip the top and bobbin threads of every stitch along a few centimetres of seam, without pulling the fabric.
  2. If the pucker relaxes, the cause is tension, or the thread and needle being too heavy. Start with Fixes 1 to 3.
  3. If the pucker stays, cut across the seam in two places and pull out all the stitching between the cuts. If one layer is now longer than the other, the layers fed unevenly. Go to Fixes 4 to 6.
  4. If the seam was flat when sewn but puckered after washing, see the section on washing.

Fix 1: Lighten and Balance the Tension

Top tension that’s too tight is one of the most common causes.

  • Rethread with the presser foot raised, so the thread seats properly in the tension discs. A thread caught on a guide or wrapped around the spool pin adds extra drag.
  • Lower the top tension slightly and sew a test. Aim for the lightest tension that still gives a balanced stitch, where the two threads lock in the middle of the layers and no bobbin thread shows on top. See our tension guide for reading the stitch.
  • Check the bobbin. It should be wound smoothly and evenly. A bobbin wound very tightly, or a bobbin case set tighter than normal, can contribute too. Most home sewers shouldn’t need to adjust the bobbin case screw, so try everything else first.

Fix 2: Adjust the Stitch Length

Very short stitches put a lot of thread into a short length of fabric, which can make a dense fabric pucker. If you’ve been sewing at a short stitch length, try a slightly longer one. A medium length around the 2.5 mm default setting on many machines is a common starting point for woven fabrics. Test on scraps, as the best length depends on the fabric.

Fix 3: Use a Finer Needle and Thread

On fine, tightly woven fabric, a large needle and thick thread push the yarns apart and cause puckering that no tension change will remove.

  • Use a fine needle suited to the fabric, such as a 60/8 or 70/10 on lightweight fabrics. A microtex (sharp) needle pierces densely woven fabrics cleanly.
  • Fit a fresh needle. A blunt or slightly burred needle drags the fabric down into the needle plate instead of piercing it.
  • Use a finer thread on delicate fabrics. A fine polyester thread is often recommended for lightweight fabrics because it’s strong for its thickness.
  • Cut on the bias where the design allows. Seams that run on the bias pucker less in tightly woven fabric than seams that run exactly along the grain.

Fix 4: Control How the Layers Feed

The feed dogs grip the bottom layer, while the presser foot presses on the top layer and slows it slightly. On slippery or thick fabrics, the top layer can creep ahead or drag behind, and the extra fabric becomes puckers.

  • Reduce the presser foot pressure if your machine has a pressure adjustment, especially on light, slippery fabric. Too much pressure can stretch the top layer. Too little can let the fabric lift with the needle.
  • Use a walking foot (even-feed foot), or your machine’s built-in dual feed if it has one. This feeds the top layer at the same rate as the bottom.
  • Pin or clip more closely, at right angles to the seam, and remove pins before they reach the foot.
  • Check the feed dogs are up and clean. Lint packed between the teeth weakens their grip. If the fabric isn’t moving through evenly at all, see why a machine isn’t feeding fabric.

Fix 5: Support Fine Fabric

  • Use a straight-stitch needle plate and foot, if your machine has them, for straight seams on fine fabric. The small single hole stops the fabric being pushed down into the wider zigzag opening. Switch back to the standard plate before using zigzag or decorative stitches, or the needle will hit the plate.
  • Sew with tissue paper or a tear-away stabiliser underneath. This gives the feed dogs something firmer to grip. Tear it away afterwards.
  • Start the seam slightly in from the edge, or start on a small scrap of fabric and sew straight onto your project, so the first stitches don’t drag the fabric into the hole.
  • Hold the thread tails for the first few stitches.

Fix 6: Handle the Fabric Gently

On very fine or slippery fabric, a technique often called taut sewing helps. Hold the fabric lightly in front of and behind the foot, keeping it gently taut, while letting the feed dogs move it at their own pace. Don’t pull or push. Pulling stretches the fabric and can bend the needle.

Sewing at a steady, moderate speed also tends to give flatter seams than stopping and starting.

Puckering After Washing

If a seam was flat when you sewed it but puckered after the first wash, the thread and fabric have probably shrunk by different amounts. Other parts of the garment, such as linings, tapes or interfacing, may also be shrinking at a different rate from the main fabric.

  • Pre-wash fabrics (and washable linings and tapes) the way you’ll wash the finished item.
  • Use polyester or poly-cotton thread where shrinkage is a concern. 100% cotton thread can shrink when wet.
  • Choose compatible interfacing and pre-shrink it if the manufacturer recommends this.

Press to Set the Seam

Pressing won’t fix a seam that’s badly puckered, but it does help small ripples. Before you open the seam, press the line of stitching flat as sewn, with the iron at the right temperature for the fabric. This “sets” the stitches into the fabric. Then open the seam and press it as the pattern directs. Gentle steam can help relax the stitching on many fabrics. Press with an up-and-down motion rather than sliding the iron along the seam, which can stretch it.

Knits: Puckered or Wavy?

On knit fabrics, a seam that ripples is often stretched rather than puckered. The fabric was pulled out of shape as it fed, so the seam ends up longer and wavy. The fixes are different: reduce the presser foot pressure, use a walking foot, use a ballpoint or stretch needle and a stretch stitch or narrow zigzag, and avoid pulling the fabric. True puckering (the seam gathered shorter) on knits usually means the tension is too tight or the stitch is too short.

Quick Checklist

  1. Rethread with the foot up, and lower the top tension slightly.
  2. Fit a new, finer needle suited to the fabric.
  3. Use a finer thread on lightweight fabric.
  4. Lengthen the stitch a little.
  5. Lighten the presser foot pressure, or use a walking foot.
  6. Try a straight-stitch plate and tissue paper on fine fabric.
  7. Guide the fabric gently, without pulling.
  8. Pre-wash fabric, and press seams flat before opening them.

If puckering comes with other faults, such as loops, skipped stitches or uneven feeding, start with our main sewing machine troubleshooting guide.

The complete guide to sewing machine troubleshooting

Sewing Machine Troubleshooting: Fixing Common Stitch Problems
Read the guide

Keep exploring

Guides from other topics

All topics →