Sewing Machine Troubleshooting

Why does my thread keep pulling out of the needle on my sewing machine?

Thread slipping out of the needle is usually down to the take-up lever position or a short tail. Here's how to start and stop a seam so it stays threaded.

On this page
  1. The Short Answer
  2. Why It Happens: The Take-Up Lever
  3. How to Start a Seam So the Thread Stays Put
  4. How to Stop a Seam Without Unthreading
  5. Other Causes
  6. If It Unthreads in the Middle of a Seam

The Short Answer

Thread usually pulls out of the needle because the take-up lever wasn’t at its highest point when you started or stopped sewing, or because the thread tail was too short. When the lever rises, it pulls thread up from the needle. If there isn’t enough slack, it pulls the end straight out of the eye. Start and stop with the needle and take-up lever fully raised, leave a tail of about 10 to 15 cm (4 to 6 inches), and hold the tails for the first few stitches. That fixes most cases.

Why It Happens: The Take-Up Lever

The take-up lever is the arm that moves up and down on the front or top of the machine as you sew. On each stitch it lets out thread while the needle goes down and the hook forms the stitch, then pulls the thread back up to tighten the stitch.

If you start sewing with the lever partway down, its first upward movement can draw thread back from the needle side rather than from the spool, because the needle thread isn’t yet held by the fabric. With a short tail, that’s enough to pull the thread out of the eye.

How to Start a Seam So the Thread Stays Put

  1. Raise the needle to its highest point. Turn the handwheel toward you until the take-up lever is at the top of its stroke. On computerised machines, the needle up/down button usually does this.
  2. Pull out a long enough tail. Leave about 10 to 15 cm (4 to 6 inches) of top thread through the needle.
  3. Bring up the bobbin thread and lay both tails under the presser foot toward the back of the machine.
  4. Place the fabric and lower the presser foot.
  5. Hold both tails lightly behind the foot for the first two or three stitches, then let go.
  6. Start slowly. A sudden fast start can whip the thread out before the first stitch has formed.

How to Stop a Seam Without Unthreading

Stopping matters just as much. If you stop with the take-up lever partway down and pull the fabric out, the thread is still wrapped around the hook below. Pulling the fabric drags thread out of the needle from the wrong direction.

  • Stop with the needle at its highest position. Turn the handwheel toward you to finish the stitch if necessary.
  • Many computerised machines can be set to always stop with the needle up. Check whether yours has a needle up/down setting.
  • Raise the presser foot, then draw the fabric gently toward the back of the machine before cutting the threads, leaving tails long enough for the next seam.

Other Causes

Tail too short after the thread cutter

Automatic thread cutters, and the small blade on the side of many machines, are convenient but can leave a short tail. If the machine unthreads every time you start after using the cutter, pull a longer tail through the needle before starting. Some machines are designed to hold the thread after cutting so the next seam starts correctly. Check your manual for how yours expects you to begin.

Threading errors

If the thread has missed a guide, the take-up lever, or the tension discs, it may be under too little control and whip free of the needle. Raise the presser foot (which opens the tension discs) and rethread completely from the spool. When the foot is lowered, you should feel resistance as you pull the thread near the needle.

Needle threaded from the wrong side

Most home machines are threaded front to back, though some older machines thread side to side. If you thread from the wrong side, the thread can sit at an angle across the eye and work loose. Check your manual for the correct direction. The thread should run down the long groove on the front of the needle and into the eye.

If you use an automatic needle threader, make sure it has pulled the loop fully through the eye. Then pull the end of the thread all the way through to make the tail.

Thread snagging at the spool

If the thread catches on the notch in the spool rim, or on the edge of a spool cap that is too small, it can jerk suddenly. That jerk can pull the thread out of the needle or snap it. Fit a cap slightly larger than the spool end, and place the spool so the thread comes off smoothly.

Needle problems

A needle with a damaged eye, or a needle too small for a thick thread, adds friction that can drag on the thread. Fit a fresh needle sized for your thread. See why your thread keeps breaking for more on matching needles and threads.

If It Unthreads in the Middle of a Seam

Thread coming out partway through a seam is less common and is usually a sign of something catching:

  • the thread snagging at the spool and jerking free
  • the thread has jumped out of the take-up lever or a guide
  • the spool has run out, or the thread has wrapped around the spool pin
  • you are pulling the fabric, which drags thread out of the needle

Rethread completely and check the spool feeds smoothly. If the thread is breaking rather than slipping out, see our guide to thread breaking and skipped stitches. If loose thread is ending up in a tangle under the fabric, see how to fix bird’s nesting.

The complete guide to sewing machine troubleshooting

Sewing Machine Troubleshooting: Fixing Common Stitch Problems
Read the guide

Keep exploring

Guides from other topics

All topics →