First, Watch What Turns
When you press the pedal and hear the motor but the needle doesn’t move, something between the motor and the needle bar isn’t passing the drive along. Finding where the drive stops tells you which part to look at.
Press the pedal briefly (a second or two at a time) and watch:
| What you see | Most likely cause |
|---|---|
| Handwheel turns, needle doesn’t | Handwheel clutch disengaged, or bobbin winder engaged |
| Motor pulley spins, belt doesn’t move | Belt slipping, stretched or too loose |
| Motor pulley spins, belt has come off or snapped | Belt off or broken |
| Motor shaft spins but its pulley doesn’t | Loose pulley set screw |
| Motor hums but nothing turns | Machine jammed or seized, or a motor fault |
| Needle moves but no stitches form | Different problem: see the last section |
On many vintage and older machines the motor and belt are on the outside, at the back or right of the machine, so you can see them directly. On most modern machines the motor and belt are inside the casing, so start with the checks you can make from outside.
If the motor only hums and nothing turns, let go of the pedal straight away. Holding the pedal down on a locked machine can overheat the motor.
Check 1: Is the Bobbin Winder Engaged?
On many machines, pushing the bobbin winder spindle across (usually to the right) puts the machine into winding mode. On some, that stops the needle on purpose. If the spindle was left in the winding position, or has stuck there, the motor runs and the needle stays still.
Push the spindle back to its sewing position and try again. On some computerised machines, the screen or a light shows that winding mode is on.
Check 2: The Handwheel Clutch (Stop-Motion Knob)
Many mechanical and vintage machines have a smaller knob or disc in the centre of the handwheel, often called the stop-motion knob or clutch knob. Loosening it lets the handwheel turn freely so you can wind a bobbin without the needle moving. It’s very easy to forget to tighten it again afterwards, or for it to work loose.
To check it:
- Hold the outer handwheel still with one hand.
- With the other, turn the inner knob in its tightening direction until it’s firmly snug. Your manual will show which way. Hand-tight is enough, so don’t use tools.
- Turn the handwheel toward you. The needle should now move with it.
If the knob tightens but the needle still won’t move, or the knob keeps loosening, the small clutch washer behind it may be missing, damaged or fitted the wrong way round. This is a cheap part on most machines. Note how the knob, washer and screw come apart before you take them off.
Check 3: The Belt
Unplug the machine before touching the belt or pulleys.
Belt off or broken
On external belt machines, the belt runs from the motor pulley to a groove in the handwheel. If it has jumped off, you can usually refit it by easing it onto the motor pulley first, then rolling it onto the handwheel groove while turning the handwheel by hand. A snapped belt needs replacing. Take the old one, or the machine’s model number, when buying, as belts come in different lengths and profiles (smooth, ribbed or toothed).
On internal belt machines you’ll need to take off a cover to see the belt. If you’re not comfortable doing that, this is a reasonable job to take to a repair shop.
Belt slipping
A belt can stay on but slip. The motor speeds up, but the machine turns slowly or stalls when the needle meets fabric. Signs include:
- The machine runs with no fabric under the foot but stops in the fabric.
- A squeal, or a smell of hot rubber.
- A shiny, hardened (“glazed”) surface on the belt, or cracks.
- A belt that’s visibly stretched or loose.
A glazed, cracked or stretched belt should be replaced. Cleaning oil off the belt and pulleys can help if oil has got onto them, but a belt that has hardened with age rarely grips well again.
Setting belt tension
On external motor machines, the motor usually hangs on a bracket with a screw that lets you raise or lower it to tighten or loosen the belt. A belt should have a little give when pressed between the pulleys. It shouldn’t be slack, and it shouldn’t be drum-tight. A belt that’s too tight makes the machine stiff to turn and puts strain on the motor bearings.
Check 4: The Motor Pulley
The small pulley on the motor shaft is usually held on by a set screw. If that screw works loose, the motor shaft spins inside the pulley and nothing else moves. With the machine unplugged, try turning the pulley by hand while holding the motor still. If the pulley turns on the shaft, line up the screw with the flat spot on the shaft (if there is one) and tighten it.
Check 5: A Jam or a Seized Machine
If the handwheel won’t turn by hand at all, or turns only with great force, the motor may be running (or humming) but unable to move the mechanism:
- Thread jam in the hook. A wad of thread around the hook or bobbin case can lock it solid. Unplug, remove the needle plate and bobbin case, and carefully cut away the tangled thread. Don’t force the handwheel. See clearing a jammed sewing machine for the full process.
- Needle stuck in thick fabric. Raise the presser foot, turn the handwheel toward you gently and ease the fabric free. See sewing thick fabric if this keeps happening.
- Old, dried oil. A machine that has stood for years can be stiff with hardened oil, especially vintage machines. Cleaning the old oil out and re-oiling with sewing machine oil at the points your manual shows often frees it. Never use cooking oil or general household lubricants.
Gears and Internal Drive Problems
If the belt, pulley and clutch are all fine but the handwheel still turns without moving the needle, the fault is inside the machine:
- A stripped or cracked gear. Some older models use plastic or nylon gears that become brittle with age. A cracked gear may spin on its shaft or skip teeth, often with a clicking sound.
- A loose set screw on a crank or gear inside the arm.
- A broken connecting part between the upper shaft and the needle bar.
These usually need the machine opened up and the parts identified for that model. Unless you’re confident with mechanical repairs, take it to a technician.
Needle Moves but No Stitches Form
This is a related but different fault. If the needle goes up and down normally but the hook underneath doesn’t turn, or doesn’t catch the thread, the problem is in the lower drive. Some machines use an internal toothed timing belt or gears to drive the hook. If that belt breaks or slips a tooth, the needle moves but no stitches form. A hook that turns but has slipped out of position also stops stitches forming. See sewing machine timing symptoms and checks for how to tell.
When to Get It Repaired
Take the machine in if:
- It’s a computerised or electronic machine and the simple checks (bobbin winder, clutch, jams) don’t solve it. The motor, belt and drive are inside and often linked to sensors.
- The motor hums but won’t turn even when the machine turns freely by hand. This may be a motor or electrical fault.
- You smell burning or see smoke. Unplug it and don’t use it again until it’s been checked.
- You find a cracked gear or a broken internal part.
A hard jam can also knock the hook out of time. If the machine runs again but now knocks or clunks, see why a sewing machine bangs.