Sewing Machine Troubleshooting

Why is my zigzag stitch only going straight?

If your zigzag sews a straight line, check the stitch width and mode first, then try a simple paper test to see whether the needle is actually swinging.

On this page
  1. The Short Answer
  2. Check the Settings First
  3. Do the Paper Test
  4. If the Needle Is Swinging but the Stitch Looks Straight
  5. If the Needle Isn’t Swinging
  6. A Zigzag That Only Catches on One Side
  7. When to Get It Looked At

The Short Answer

The most common reason a zigzag stitch sews straight is that the stitch width is set to zero or the wrong stitch is selected. If the settings are right, the next step is to find out whether the needle is moving side to side at all. If it isn’t, on an older mechanical machine the zigzag mechanism is often stuck with old oil or debris, and on a computerised machine a setting such as straight-stitch plate mode may be restricting it. If the needle is swinging but the stitch still looks straight, the cause is usually tension, stitch length or threading.

Check the Settings First

Stitch width at zero

On machines with a separate stitch width dial or lever, a zigzag only appears when the width is above zero. With the width at 0, the zigzag stitch simply sews a straight line. Turn the width up to a medium setting and try again. On some machines the width dial can be knocked easily, or reset when you change stitches.

Change the width only when the needle is raised out of the fabric. On many machines, adjusting it with the needle down can bend the needle.

Wrong stitch or mode selected

On a computerised machine, check the screen shows the zigzag stitch and a width above zero. Some machines remember the last width used for each stitch, so it may have been set narrow or to 0 previously.

Straight-stitch plate or foot setting

Some computerised machines have a setting you switch on when a straight-stitch needle plate or straight-stitch foot is fitted. A twin-needle setting can also limit how wide stitches can go. While the setting is on, the machine may restrict or block zigzag stitches to protect the needle. Check your machine’s settings menu, and if you have changed back to the standard plate, switch the setting off.

If you do have a straight-stitch plate or foot fitted, swap it for the standard zigzag plate and foot before you sew a zigzag. Otherwise the needle can hit it and break. See why needles keep breaking.

Do the Paper Test

This simple test tells you whether the problem is mechanical or a thread issue:

  1. Unthread the machine and remove the bobbin.
  2. Select a zigzag and set it to the widest width.
  3. Place a piece of plain paper under the presser foot and sew slowly for a few centimetres.
  4. Look at the holes.
  • Two rows of holes, alternating side to side: the needle is swinging. The machine’s zigzag mechanism is working, and the problem lies with tension, stitch length or threading.
  • A single straight line of holes: the needle isn’t moving sideways. The problem is in the settings or the mechanism.

Use an old needle for this test, as paper dulls needles. Change the needle afterwards.

If the Needle Is Swinging but the Stitch Looks Straight

If the paper test shows a zigzag pattern, the stitch is being formed but is being pulled into a line, or is too dense to see:

  • Upper tension too high. Tight top tension can pull a narrow zigzag into a ridge that looks almost straight, and can make the fabric tunnel underneath. Lower the upper tension a little and test. Our tension guide explains how.
  • Stitch length very short. A very short length with a narrow width gives a dense satin stitch that can look like a thick straight line. Increase the length.
  • Width set very narrow. A width of around 1 mm can be hard to tell apart from a straight stitch on some fabrics.
  • Threading error. If the top thread missed the tension discs, the stitch can sit badly. Rethread with the presser foot raised.
  • Lightweight fabric bunching. Very fine fabric can gather up under a zigzag so it looks like a line. A stabiliser or tissue paper underneath helps.

If the Needle Isn’t Swinging

Older mechanical machines: gummed-up mechanism

On older mechanical zigzag machines, the parts that swing the needle bar from side to side can stick when old oil thickens or dust builds up. This often happens after a long time in storage, and a general clean and oil of a vintage machine is a good place to start. You may notice that the width dial or lever feels stiff, or moves but has no effect.

If your manual shows oiling points for the zigzag mechanism, unplug the machine, remove the top or side cover as your manual describes, apply a drop of sewing machine oil to the pivot points, then move the width control back and forth gently while turning the handwheel by hand. It can take some time for oil to soften old residue. Don’t force a stiff control, as some machines have plastic parts that can crack. If it doesn’t free up, take it to a technician.

Cam and lever machines

Some vintage machines create zigzag and decorative stitches with cams, either built in or as removable discs. Depending on the model, you may need to move a lever or knob to engage the zigzag, or fit the right cam. If the cam isn’t engaged or fitted, the machine may only sew straight. Check the manual for your model. Many vintage manuals are available from manufacturers or collector sites online.

Computerised machines

On a computerised machine the needle swing is driven electronically. If the settings are right and the plate setting is off, but the needle still won’t swing, try switching the machine off and on again. If it still won’t zigzag, and especially if it shows an error message, contact the manufacturer or an authorised service centre. Internal faults on electronic machines are generally not something to repair at home.

A Zigzag That Only Catches on One Side

If the needle swings but the stitch only forms on one side, so you see a straight line of stitches with loose loops or gaps on the other side, the hook may be catching the thread loop correctly at one needle position but missing it at the other. A new needle, pushed fully up, sometimes fixes this. If it doesn’t, this pattern is a common sign of hook timing that is slightly out. See our guide to sewing machine timing symptoms.

When to Get It Looked At

Have the machine serviced if:

  • the paper test shows a straight line with the settings correct
  • the width control is jammed, broken or turns without effect after oiling
  • the zigzag catches on one side only with a new needle
  • a computerised machine won’t zigzag and shows an error

For other stitch problems, the main troubleshooting guide has a symptom finder.

The complete guide to sewing machine troubleshooting

Sewing Machine Troubleshooting: Fixing Common Stitch Problems
Read the guide

Keep exploring

Guides from other topics

All topics →