What Balanced Tension Looks Like
A sewing machine forms each stitch by pulling the top thread and the bobbin thread together so they lock inside the fabric. The top thread is controlled by the tension discs and the dial on the machine body. The bobbin thread is controlled by a small spring on the bobbin case.
When the two are balanced:
- the top side shows only top thread, in a smooth line
- the underside shows only bobbin thread
- neither side has loops, dots of the other colour, or puckering
The easiest way to check is to sew a test seam on two layers of your project fabric, with a different colour in the bobbin from the top. Any tension imbalance is then obvious.
Which Thread Is Actually Loose?
The names cause a lot of confusion. A “loose bottom stitch” (loops on the underside) is usually caused by the top thread being too loose, not the bobbin.
| What you see | What it usually means | What to adjust |
|---|---|---|
| Loops or slack top thread on the underside | Top tension too low, or top threading error | Rethread; then raise upper tension |
| Top thread lying flat along the underside | Top tension too low | Raise upper tension |
| Bobbin thread pulled up as dots on top | Top tension too high, or bobbin too loose | Lower upper tension first |
| Loose, slack stitches on top | Bobbin tension may be too low, or top too tight | Lower upper tension; check bobbin |
| Puckering along the seam | Tension too high overall, among other causes | Lower upper tension; see puckering guide |
Before You Touch the Dial
Most “tension problems” turn out to be threading problems. Check these first, because they are quick and they are the usual cause:
- Rethread the top with the presser foot raised. The foot must be up for the thread to slip between the tension discs. Rethread from the spool, not just the needle.
- Lower the presser foot before sewing. The discs only grip the thread when the foot is down. Sewing with it up gives loops underneath almost at once.
- Check the bobbin. It should be evenly wound, the correct type for your machine, inserted the right way round, and pulled through its tension slot.
- Fit a fresh needle of the right size for the thread.
- Use the same thread weight top and bottom. A heavy top thread with a fine bobbin thread, or the reverse, makes balance hard to achieve.
- Clean lint from between the tension discs (floss gently with an unwaxed piece of thread, with the foot raised) and from the bobbin area.
If the stitch is still unbalanced after all of this, then adjust tension.
Adjusting Upper Tension
Adjust the upper tension, not the bobbin, in most cases. It’s easier to change and easier to reset.
- Make a note of the current setting.
- Turn the dial one number, or half a number, in the direction you need.
- Sew a test seam on scrap of the same fabric, using the same thread and stitch.
- Repeat until the stitch looks balanced on both sides.
Change one thing at a time. Write down the setting that works for each fabric and thread combination, so you have a reference next time. Stretch fabrics have their own quirks, covered in our guide to tension and stretch stitches for knit fabric.
Is a higher number tighter?
Yes. On almost all home sewing machines, a higher number means tighter upper tension and a lower number means looser. To loosen upper tension, turn the dial toward the lower numbers. Many machines have a general-purpose setting somewhere around the middle of the dial, often near 4, but the right setting depends on the fabric, thread and stitch. A zigzag or decorative satin stitch often looks better with slightly less upper tension.
Computerised machines may set tension automatically, but most still let you override it. Check your manual.
Adjusting Bobbin Tension
Bobbin tension is set at the factory and usually doesn’t need changing for ordinary sewing. Adjust it only when upper tension changes don’t fix the balance, or when you have deliberately changed to a very different bobbin thread.
Removable bobbin cases and the drop test
Machines with a separate metal bobbin case, usually front-loading, have a small screw on the tension spring of the case. One widely used home check is the drop test:
- Put a wound bobbin in the case and pull the thread through the spring as normal.
- Hold the thread end and let the case hang.
- Give it a small jerk upward. With tension that suits general sewing, the case should slide down a short way and then stop. If it drops freely, the tension is too loose. If it doesn’t move at all, it may be too tight.
The test is a rough guide, not a precise measurement, but it helps spot a case that is badly out.
To adjust:
- Mark the screw’s starting position with a marker dot first, so you can return to it.
- Turn clockwise to tighten and counter-clockwise to loosen (“righty-tighty”).
- Make very small turns, a fraction of a turn at a time; a quarter turn is already a large change. Retest after each turn.
- Work over a towel or tray. The screw is tiny and easy to lose, and turning it too far can remove it entirely.
Some sewists keep a second bobbin case for specialty threads so the main case stays at its factory setting.
Drop-in bobbins
On machines with a drop-in (top-loading) bobbin, the case is fitted into the machine and many manufacturers advise against adjusting its tension at home. If you suspect the drop-in case’s tension is wrong after ruling out everything else, check your manual or ask a technician. Make sure the bobbin is the type specified and spins in the right direction, because these mistakes are far more common than a case that is out of adjustment.
Why Is My Bobbin Thread Wiggly?
A wavy or wiggly line of bobbin thread on the underside, with the top thread pulling it into kinks, often means the top tension is a little high relative to the bobbin, or the bobbin was wound unevenly or too loosely. Rewind the bobbin at a steady speed using the machine’s bobbin winder, rethread it through its tension slot, then reduce upper tension slightly and test. If loops of top thread appear underneath instead, the top is too loose. See our guide to fixing thread bunching underneath.
When Tension Won’t Stay Set
If you balance the stitch and it drifts again within the same seam or session:
- Lint or thread fragments in the discs can stop them closing evenly. Clean them as described above.
- The thread may be jumping out of the discs because of a snag at the spool or a missed guide.
- A worn or damaged tension assembly or check spring can stop holding steady tension. This is a repair job rather than an adjustment.
- Uneven thread can vary in thickness along its length. Try a different spool.
If the balance keeps shifting along with skipped stitches and thread breaks, see why thread keeps breaking and skipping stitches. If the seam gathers even when the stitch looks balanced, see how to stop seams puckering.