Short Answer
A sewing machine usually stitches backwards for one of a few simple reasons:
- The reverse lever or button is stuck in the engaged position.
- The buttonhole lever has been pulled down.
- A stitch that moves backward as part of its pattern has been selected.
- On some machines, the stitch length control is set in its reverse range.
Less often, lint, dried oil or a worn part in the feed mechanism stops the feed from returning to forward. Start with the quick checks below, as they solve most cases.
First, Confirm What’s Happening
Sew slowly on a scrap of fabric and watch it:
- The fabric moves toward you (backward) the whole time: the feed is stuck in reverse. Work through the checks below.
- The fabric moves forward and back, but makes overall forward progress: you’ve probably selected a stretch or decorative stitch that works this way by design.
- The fabric doesn’t move at all: that’s a different problem. The feed dogs may be lowered, the stitch length set to 0, or the presser foot not lowered. See why your sewing machine isn’t feeding fabric.
Quick Checks, in Order
Switch the machine off before poking around the needle area.
1. Reverse Lever or Button Stuck
The reverse lever or button may not be springing back fully after use.
- Mechanical machines: press the reverse lever down and release it firmly a few times. See if it returns fully to its rest position. Lint or a sticky spring can hold it partly engaged.
- Computerised machines: press and release the reverse button a few times. Check that nothing (a pin, a fabric scrap, a sticker) is pressing on it.
Our guide to using the backstitch button explains how the reverse control should behave.
2. Buttonhole Lever Down
Many machines with one-step buttonholes have a buttonhole lever on the left of the needle area. It’s pulled down when you sew a buttonhole and should be pushed back up afterwards. If it’s down, or has been knocked down, the machine can sew parts of the buttonhole sequence, including backward sections. Push it all the way back up into its home position.
3. A Stitch That Moves Backward by Design
Several common stitches move the fabric back and forth as they sew:
- Triple straight (stretch) stitch: forward, back, forward
- Some stretch, overlock and decorative stitches
- Buttonhole sequences, where one side is often sewn backward
Select the plain straight stitch (often stitch 1 or “00”, centre needle) at about 2.5 mm length and test again.
4. Stitch Length Dial in the Reverse Range
On some machines, particularly older mechanical models, forward and reverse are on the same stitch length control. Forward lengths are on one side of zero and reverse on the other, or reverse is engaged by moving the lever past a point. If the control has been moved into the reverse range, the machine sews backward continuously. Set it back to a normal forward length and check your manual for how your model’s control works.
5. Feed Balance Setting
Some machines have a feed balance (or stretch stitch adjustment) control that fine-tunes how far the fabric moves forward and backward in stretch and decorative stitches. If it’s far off-centre, a stitch may drift backward or look distorted. Return it to its neutral position, which is usually marked.
6. Reset a Computerised Machine
On computerised machines, switch the machine off, wait a short while, and switch it on again so it goes back to its default stitch. Brother’s support site, among others, has troubleshooting guidance for machines stuck in reverse, so it’s worth checking your manufacturer’s help pages for your model.
When the Cause Is Mechanical
Lint and Old Oil in the Feed Mechanism
This is especially common on vintage or long-stored machines. Old oil can dry to a sticky varnish, and lint can pack into the feed dog area. Either can stop the feed mechanism from returning to forward after reverse is used.
- Remove the needle plate (if your manual allows) and brush out the lint around and under the feed dogs.
- If your manual shows oiling points and the machine is designed to be oiled by the owner, apply a drop of sewing machine oil, never household oils, to the indicated points. Then work the reverse lever and handwheel by hand to free it.
- Don’t oil machines whose manuals say they don’t need it. Computerised machines in particular should follow the manufacturer’s instructions.
Worn or Broken Parts
A broken spring, a worn linkage or a damaged part in the reverse mechanism can keep the feed stuck in reverse. These aren’t usually user repairs.
When It’s Not Really Reversing
Sometimes stitching looks backward:
- You’re pulling the fabric toward you without realising it. Let the feed dogs do the work.
- The feed dogs are dropped or the stitch length is 0, so the stitches pile up in one spot.
- The fabric is too thick or sticky to feed, so it drags. A walking foot or non-stick foot can help. See our guide to presser feet.
When to See a Technician
Book a service if:
- The machine stays in reverse after you’ve checked the reverse control, buttonhole lever, stitch selection and stitch length
- The reverse lever feels loose, floppy or disconnected
- You hear grinding or clunking from the feed area
- A computerised machine shows an error message, or keeps defaulting to reverse after a reset
How to Prevent It
- Push the buttonhole lever up after every buttonhole.
- Clean lint from the needle plate and bobbin area regularly.
- Oil only as your manual directs.
- Have the machine serviced periodically, especially if it’s vintage or hasn’t been used for a long time.
For general machine setup and care, see our beginner’s guide to using a sewing machine.