A presser foot holds the fabric flat against the feed dogs while the machine stitches, and different feet are shaped to make particular jobs easier. Most sewing can be done with a handful of feet: an all-purpose (zigzag) foot for everyday seams, a zipper foot for sewing close to zipper teeth and piping, a buttonhole foot, and often a blind hem and overcast foot. Specialist feet such as the walking foot, quarter-inch foot and free-motion foot make specific tasks, like quilting, accurate patchwork and darning, much more manageable.
This guide explains what each common foot does, how to check whether a foot will fit your machine, and which ones are worth adding first.
What a presser foot does
When you lower the presser foot lever, the foot presses down on the fabric. That pressure keeps the fabric in contact with the feed dogs, the moving teeth under the needle plate, so the fabric moves forward evenly with each stitch. Without the foot, the fabric would lift with the needle and stitches wouldn’t form properly.
Different feet change how that happens:
- The shape of the underside, which may be flat, grooved or tunnelled, controls how the foot rides over stitches or bulky edges.
- The opening around the needle determines which stitches can be sewn and how much you can see.
- Guides, flanges and blades help you stitch at a fixed distance from an edge.
- Extra mechanisms, such as the top feed dogs on a walking foot, change how the layers move.
For where the foot sits in relation to the other parts, see our guide to sewing machine parts and terms.
Before you buy: will it fit your machine?
Presser feet are not universal. Check these points before buying a foot, especially a generic one.
Shank type
The shank is the part of the machine the foot attaches to, at the bottom of the presser bar. Home machines generally have one of three types:
- Low shank: The most common type on modern domestic machines. As a rough check, the distance from the bottom of the foot to the centre of the presser bar screw is about 1/2 inch (around 13 mm).
- High shank: Found on some domestic machines and many industrial machines. The same measurement is roughly 1 inch (around 25 mm).
- Slant shank: Used on certain vintage Singer models, where the presser bar is angled rather than vertical.
Some brands also use their own proprietary attachment systems. Your manual or the manufacturer’s accessory list is the most reliable way to confirm what your machine takes.
Snap-on vs screw-on
- Snap-on feet clip onto a presser foot holder (also called an ankle or shank adapter) that stays screwed to the presser bar. Most modern machines work this way, and changing feet takes seconds.
- Screw-on feet attach directly to the presser bar with a thumbscrew. Walking feet, free-motion feet and many older or specialist feet are screw-on.
Stitch width and needle clearance
This is the point most often overlooked, and it matters for safety. Machines have different maximum zigzag widths. Many home machines go up to 5 mm, while others go to 7 mm or 9 mm. A foot designed for a 5 mm machine may have a narrower needle opening than a 7 mm machine’s widest stitch.
If the needle swings wider than the opening in the foot, or if you use a zigzag or moved needle position with a foot that only has a single small hole, the needle can strike the foot and break. To avoid this:
- Check that a foot is designed for your machine’s maximum stitch width.
- Before sewing with a new foot or stitch, turn the handwheel slowly by hand through a full stitch cycle, at the widest setting you’ll use, to make sure the needle clears the foot and needle plate.
- Return to centre needle position before fitting straight-stitch-only feet.
How to change a presser foot
The exact method varies, so check your manual, but for most snap-on systems:
- Turn the machine off, or use its lock mode if it has one.
- Raise the needle to its highest position and lift the presser foot lever.
- Press the release button or lever at the back of the presser foot holder. The foot drops off.
- Place the new foot under the holder so its crossbar (pin) lines up with the groove in the holder.
- Lower the presser foot lever. The foot should snap into place.
- Turn the handwheel by hand to check needle clearance.
For screw-on feet, you loosen the presser bar screw, remove the holder or old foot, fit the new foot onto the bar and tighten the screw. Walking feet usually also have an arm or fork that must sit over the needle clamp screw.
The feet most machines come with
The exact set depends on the machine, but these are the most commonly included feet.
All-purpose (zigzag) foot
The standard foot that’s usually already attached. It has a wide opening for zigzag and most utility stitches and handles the bulk of everyday sewing on woven fabrics, including straight seams, zigzag edge finishing and basic decorative stitches. Some brands label it with a letter or number in the manual; Brother, for example, calls its standard zigzag foot “J.”
Zipper foot
A narrow foot that sits to one side of the needle so you can stitch right next to zipper teeth. Depending on the design, you either clip it on to the left or right of its holder or slide it sideways, or you move the needle position instead. It’s also used for piping, cording and anything else where you need to sew close to a raised edge. See our guide to sewing a zipper with a sewing machine for how to use it.
Buttonhole foot
On machines with a one-step buttonhole, this is usually a long sliding foot with a button holder at the back, which tells the machine how long to make the buttonhole. On four-step machines, it’s often a shorter foot with markings to help you judge length. Our buttonhole tutorial walks through both.
Overcast (overedge) foot
Has a small bar or brush that the zigzag or overcast stitch wraps around at the fabric edge. This stops the edge from being pulled into a tunnel and gives a neater finish to raw edges. It doesn’t trim the fabric the way a serger does, but it’s a practical substitute for edge finishing.
Blind hem foot
Has a guide (often adjustable) that keeps the folded edge of a hem aligned with the blind hem stitch, so the stitch only just catches the fold. The result is a hem that is barely visible from the right side on trousers, skirts and curtains. It takes some practice to set up, so test on a scrap.
Satin stitch / embroidery foot
Has a channel or groove underneath so the foot can ride over the raised, dense thread of satin stitches and decorative stitches without getting stuck. It’s often made of clear plastic, or cut away at the front, so you can see the stitches as they form.
Button sewing foot
A short foot with a grippy or rubber-lined underside that holds a flat button in place while the machine sews a zigzag back and forth through its holes. Feed dogs are usually lowered for this, and the zigzag width must match the distance between the button’s holes. Check it by turning the handwheel by hand before stitching.
Useful feet to add
If your machine didn’t come with these, they’re among the most frequently recommended additions.
Walking (even feed) foot
A bulky screw-on foot with its own set of feed dogs that move the top layer of fabric in step with the machine’s feed dogs underneath. This helps stop layers from shifting, so the top layer doesn’t end up longer than the bottom. It’s widely used for:
- Quilting straight lines through the quilt sandwich
- Matching plaids and stripes
- Thick or spongy layers, such as fleece and wadding
- Some slippery or stretchy fabrics
Walking feet are machine-specific, so buy one listed as compatible with your model.
Quarter-inch foot
Built so the edge of the foot, sometimes with a guide flange, sits exactly 1/4 inch from the centre needle. That is the standard seam allowance for most patchwork, and the foot makes accurate piecing much easier.
Edge-stitch foot
Has a central blade or flange that runs along a fabric edge or seam, keeping the stitching a consistent, small distance from it. It’s ideal for topstitching, edge-stitching and stitching in the ditch, and changing the needle position changes the distance from the edge. Our article on sewing straight lines covers other guide options too.
Invisible zipper foot
Has two tunnels underneath that uncurl the coils of an invisible (concealed) zipper, so you can stitch right next to them. The finished zipper disappears into the seam. A standard zipper foot can be used in a pinch, but results are usually neater with the dedicated foot.
Non-stick foot
Made of, or coated with, a slippery material (often PTFE, sometimes sold as a “Teflon” foot). It glides over fabrics that tend to stick to a metal foot, such as vinyl, laminated cotton, faux leather and some coated fabrics.
Roller foot
Has small rollers that turn as the fabric moves, rather than sliding over it. It’s another option for leather, vinyl and some knits, and for thick fabrics that resist feeding.
Open-toe foot
A variant of the satin stitch foot with the front cut away completely, giving a clear view of the needle. It’s used for appliqué, decorative stitching and any work where you need to follow a line precisely.
Specialist feet
These are worth buying when a project calls for them, rather than up front.
Free-motion / darning foot
Used with the feed dogs lowered or covered, so you move the fabric in any direction yourself. The foot hovers just above the fabric or hops up and down with each stitch. It’s used for free-motion quilting, thread painting and darning. Embroidery machines may use a similar foot for embroidery mode, as described in their manuals.
Rolled hem foot
Has a curled scroll at the front that rolls a very narrow double hem as you sew. It’s suited to lightweight fabrics like chiffon, voile and lawn, for scarves, ruffles and fine hems. Rolled hem feet come in different widths and need practice to feed evenly.
Gathering foot
Gathers fabric as you sew, with the amount of gathering affected by stitch length and tension. Some versions can gather one layer while sewing it to a flat second layer at the same time.
Bias binding foot
Folds pre-made bias tape around a raw edge as it feeds and stitches it in place. Many are adjustable for different tape widths; check what widths a particular foot accepts.
Cording / braiding foot
Has holes or grooves that guide one or more cords, yarns or narrow braids under the needle while you stitch over them with a zigzag or decorative stitch. It’s used for decorative couching and trims.
Straight stitch foot
Has a small round hole instead of a wide slot, giving more support to the fabric around the needle. It can help prevent fine fabrics from being pushed down into the needle plate. It must only be used with a straight stitch in the centre needle position; any zigzag or offset needle position will hit the foot.
Quick reference: which foot for which job
| Job | Foot to try |
|---|---|
| Everyday seams and zigzag | All-purpose (zigzag) foot |
| Standard zipper, piping | Zipper foot |
| Invisible zipper | Invisible zipper foot |
| Buttonholes | Buttonhole foot |
| Finishing raw edges | Overcast foot |
| Near-invisible hems | Blind hem foot |
| Very narrow hems on light fabric | Rolled hem foot |
| Satin and decorative stitches | Satin stitch / open-toe foot |
| Topstitching close to an edge | Edge-stitch foot |
| Accurate 1/4-inch patchwork seams | Quarter-inch foot |
| Quilting straight lines, thick layers, matching stripes | Walking foot |
| Free-motion quilting, darning | Free-motion / darning foot |
| Vinyl, faux leather, coated fabrics | Non-stick or roller foot |
| Attaching flat buttons | Button sewing foot |
How to identify a foot you already have
Accessory boxes often contain feet without labels. To work out which is which:
- Check the manual. Most include a picture of each supplied foot and its letter or number code. Codes are brand-specific, so a “J” foot on one brand isn’t necessarily the same as a “J” on another.
- Look for markings on the foot itself. Many feet have a small letter or number stamped on them.
- Look at the underside. A deep groove usually means a satin stitch foot; two tunnels suggest an invisible zipper foot; a rubber pad suggests a button foot; a wire or bar at the edge suggests an overcast foot.
- Look at the shape. A narrow foot on one side of the needle is a zipper foot; a long sliding frame is a buttonhole foot; a guide plate on the right is often a blind hem or edge-stitch foot.
Branded vs generic feet
Feet from your machine’s manufacturer are designed for your model and are the safest choice, but they generally cost more. Generic and multi-pack feet are widely sold and many work well, but fit and finish vary. If you buy generic feet:
- Make sure the shank type and attachment system match your machine.
- Check that the needle opening suits your machine’s maximum stitch width.
- Before sewing, turn the handwheel by hand to confirm the needle passes cleanly through the foot.
- Test on a scrap to check that the fabric feeds smoothly.
For most beginners, the feet that came with the machine are enough to get started. A walking foot, quarter-inch foot or edge-stitch foot is often the first worthwhile addition, depending on whether you lean toward quilting or garment sewing. If you’re still learning the basics, our beginner’s guide to using a sewing machine is a good next step.