Fabrics and Needles

Tension Settings and Stretch Stitches for Knit Fabric

How to set thread tension for knit fabric, read a test seam, and choose between zigzag, lightning, triple and three-step stretch stitches, including on Singer Heavy Duty.

On this page
  1. Start with balanced tension, not a “knit setting”
  2. How to read a test seam on knit fabric
  3. Tension problems that are really something else
  4. Which stretch stitch to use
  5. The triple stitch: what it’s good for and what it isn’t
  6. Finding stretch stitches on a Singer Heavy Duty
  7. Twin-needle hems and tension
  8. Quick settings for cotton jersey

Start with balanced tension, not a “knit setting”

There’s no special tension number for knit fabric. The goal is the same as for any fabric: a balanced stitch, where the top and bobbin threads interlock in the middle of the fabric layers, so you can’t see bobbin thread on top or loops of top thread underneath.

On many home machines with a numbered dial, the default sits somewhere around the middle of the range, often marked or highlighted. That default is the best place to start for knits too. Change tension only after you’ve sewn a test seam and can see a specific problem. Then adjust in small steps, about half a number at a time.

How to read a test seam on knit fabric

Sew a test seam on two layers of your actual fabric, cut in the same direction as the real seam, with the stitch you plan to use. Then check:

  • The top side: if bobbin thread shows as little dots on top, the upper tension is probably too tight (or the bobbin is threaded wrong).
  • The underside: if top thread lies in loops or straight lines on the bottom, the upper tension is probably too loose. Very often the real cause is that the machine was threaded with the presser foot down, so the thread missed the tension discs. Rethread with the foot raised before touching the dial.
  • The stretch test: pull the seam firmly in the direction the garment will stretch. If threads snap, the stitch doesn’t have enough give for that fabric, and changing tension won’t fix it.
  • The flatness: a zigzag that pulls the fabric into a raised ridge (“tunnelling”) may need a little less upper tension or a narrower width.

Tension problems that are really something else

Many problems blamed on tension when sewing knits have other causes:

Symptom Usually caused by Fix
Skipped stitches Wrong needle type or a worn needle New jersey or stretch needle; try another size
Wavy, stretched-out seam Presser foot pressure too high; fabric pulled while sewing Lower foot pressure; walking foot; let the feed dogs work
Seam breaks when stretched Straight stitch or cotton thread Stretch stitch or zigzag; polyester thread
Fabric chewed into the needle plate Starting right at the edge of a fine knit Hold thread tails; start on stabilizer
Puckered seam on a fine knit Stitch too short or tension too high Lengthen the stitch slightly; ease upper tension a little

If you’ve fixed the needle, stitch and foot pressure and the stitch still isn’t balanced, then adjust tension. Our answer on which needle to use for stretchy fabric covers the needle side in more detail.

Which stretch stitch to use

Most modern machines have at least a few of these. Names and symbols vary, so check your manual.

Stitch What it looks like Good for Notes
Narrow zigzag Small even zigzag Seams on most knits; works on any machine with zigzag Try about 1–1.5 mm wide, about 2.5 mm long
Lightning bolt (stretch straight) Almost straight, with slight angles Seams that should look like a straight stitch Sews slowly; harder to unpick than a zigzag
Triple straight stitch Thick straight line Stress points, crotch and armhole seams, topstitching Very strong; not as stretchy as zigzag-based stitches
Three-step (multi-step) zigzag Zigzag made of small straight stitches Attaching elastic, finishing edges, mending Lies flatter than a plain zigzag
Overlock-style stitch Straight stitch plus overcasting Seaming and finishing in one pass Works best with an overcast or overlock foot if your machine has one
Honeycomb and decorative stretch stitches Patterned Decorative seams on activewear, smocking-style effects Use thread in both top and bobbin that matches the fabric

For a typical cotton jersey T-shirt, a narrow zigzag or lightning bolt for seams and a twin needle for hems is a simple, reliable combination.

The triple stitch: what it’s good for and what it isn’t

The triple straight stitch (often labelled “straight stretch”) moves the fabric forward, back and forward again, so each stitch is sewn three times. That makes it one of the strongest stitches on a home machine, which is why it’s popular for:

  • crotch seams and underarm seams that take a lot of strain;
  • bold topstitching with regular thread, as a substitute for thick topstitching thread;
  • seams on stretch denim and other fabrics with moderate stretch.

Two things to know before you use it everywhere:

  • It has limited stretch. The back-and-forth motion builds in a little extra thread, so it has more give than a single straight stitch. On very stretchy fabrics like swimwear Lycra, though, a zigzag-based stitch is usually a safer choice.
  • It’s very hard to unpick. Sew a basting fitting with an ordinary long straight stitch first, then use the triple stitch for the final seam.

Most machines need you to select it from the stitch menu or dial. On some mechanical machines it’s only available when the stitch length dial is turned to a special stretch setting, as described below.

Finding stretch stitches on a Singer Heavy Duty

Many mechanical Singer Heavy Duty models, such as the 4423, treat stretch stitches as a separate group. On these machines the stretch and reinforced stitches are usually marked in a different colour on the stitch selector. You reach them by turning the stitch length dial to its stretch setting, which is marked S1 on several models, instead of to a normal length. Then you pick the stitch you want, such as the straight stretch (triple) stitch, a reinforced zigzag, or a multi-step zigzag.

Model details vary, so check the manual for your exact machine. If a Heavy Duty machine seems to be sewing back and forth when you expected a plain straight stitch, the stitch length dial is often sitting on the stretch setting.

These machines can also sew jeans, with the right needle and some patience at thick seam intersections. See can I sew denim on a regular sewing machine for the setup.

Twin-needle hems and tension

A twin needle uses one bobbin thread to link two top threads, so tension has a big effect on the result:

  • If a raised ridge forms between the rows, lower the upper tension slightly and try a slightly longer stitch.
  • Put a strip of lightweight fusible knit interfacing or wash-away stabilizer in the hem allowance to support the fabric.
  • Use a stretch or jersey twin needle, not a universal one, on knits.
  • Sew slowly and keep the hem flat. Don’t stretch it as it feeds.

Quick settings for cotton jersey

As a starting point (always test first):

  • Needle: jersey/ballpoint 75/11 or 80/12
  • Thread: all-purpose polyester, top and bobbin. See what kind of thread to use for stretch fabric for alternatives.
  • Seam stitch: narrow zigzag (about 1–1.5 mm wide, 2.5 mm long) or lightning bolt
  • Tension: your machine’s default, adjusted only after testing
  • Presser foot pressure: slightly reduced, if adjustable
  • Hem: stretch twin needle with a straight stitch, or see the lettuce hem tutorial for a decorative edge

For the wider picture of sewing knits on a regular machine, including when a serger helps, see our guide to sewing stretchy and tricky fabrics.

The complete guide to fabrics and needles

Sewing Stretchy and Tricky Fabrics on a Sewing Machine
Read the guide

Keep exploring

Guides from other topics

All topics →