Machine Embroidery

Machine Embroidery Stabilizers: Which Type to Use for Every Fabric

Which stabilizer should you use for machine embroidery? A guide to cutaway, tearaway, washaway and toppers, with a fabric-by-fabric chart and tips.

On this page
  1. The quick answer
  2. Why stabilizer matters
  3. The main types of stabilizer
  4. Stabilizer by fabric
  5. How design density changes the choice
  6. Weight, color and quality
  7. How to use and remove stabilizer
  8. Common mistakes

The quick answer

The fabric decides the type of stabilizer, and the design decides how much you need.

  • Stretchy fabric (knits, T-shirts, sweatshirts, polos): use cutaway. A common rule is “if it stretches, cut it away.”
  • Stable woven fabric (quilting cotton, denim, canvas, linen): tearaway usually works, but switch to cutaway for very dense designs.
  • Sheer fabric, or projects where no backing should remain (organza, tulle, free-standing lace): use washaway.
  • Textured or pile fabric (towels, fleece, velvet, corduroy): add a water-soluble topper on top, plus a suitable backing underneath.
  • Fabric you shouldn’t hoop (leather, vinyl, some velvets): hoop a sticky stabilizer and float the fabric on top.

The rest of this guide explains why, and how to handle the in-between cases.

Why stabilizer matters

A single embroidery design can put thousands of stitches into a small area. Each one pulls on the fabric. Without enough support, the fabric shifts, puckers and stretches out of shape while it stitches, and outlines stop lining up with fills.

The stabilizer, also called backing, holds the fabric steady while it’s stitched. Permanent types also keep supporting the design through wearing and washing. Getting it right prevents a long list of problems, including puckering, gaps, outlines out of register, skipped stitches and thread breaks from fabric bouncing with the needle.

The main types of stabilizer

Cutaway

Cutaway is a soft, non-woven or mesh material that stays in the item permanently. After stitching, you trim the excess around the design. Because it doesn’t break down, it keeps supporting the stitches every time the garment is stretched or washed.

  • Use it for: all knits, including T-shirts, jersey, sweatshirts, polos, fleece and performance wear. Also for dense designs on any fabric.
  • No-show mesh (also called poly mesh) is a light, sheer cutaway. It’s popular for light-colored T-shirts because it doesn’t show through, and it’s soft against the skin.
  • Fusible cutaway irons onto the back of the fabric before hooping. That’s helpful for very stretchy knits.

Tearaway

Tearaway is a firm, paper-like non-woven material. After stitching, you tear the excess away and the stitches are left without backing.

  • Use it for: stable woven fabrics that don’t need long-term support, such as quilting cotton, denim, canvas, linen, twill and towels (with a topper). Also for caps.
  • Good tearaway tears cleanly in every direction. If it only tears one way, it may stretch one way while you stitch.
  • It’s not a good choice for knits on its own. Once you tear it off, the stretchy fabric has no support and the design can distort.

Washaway (water-soluble)

Washaway dissolves in water. It comes as a clear film or as a fibrous, fabric-like sheet.

  • Use it for: sheer fabrics like organza, tulle and chiffon, where you don’t want any backing left behind. Also for lace and free-standing lace (FSL), where the design is stitched onto the stabilizer alone and becomes its own fabric once the stabilizer is washed out. FSL usually needs a heavier fibrous washaway or several layers of film.
  • The item must be washable, and the thread colorfast.

Toppers

A topper is usually a thin water-soluble film laid on top of the fabric. It stops stitches sinking into pile or texture, so small lettering and fine details stay visible.

  • Use it for: towels, terry cloth, fleece, minky, velvet, corduroy, chunky knits and other fabrics with loft or nap.
  • Tear away the excess after stitching, and dab or rinse away what’s left.

Adhesive (sticky) stabilizers

These have a paper-covered sticky surface. You hoop the stabilizer alone, score and peel the paper, then press the fabric onto the sticky surface. This is called “floating” the fabric.

  • Use them for: items you can’t or shouldn’t hoop, such as leather, vinyl, velvet, collars, cuffs, pockets, and small or awkward pieces.
  • Adhesive can build up on the needle and cause problems. Some embroiderers prefer to hoop plain stabilizer and hold the fabric with a basting stitch or light spray adhesive instead.
  • Some versions, sometimes called wet-and-stick, become sticky when you dampen them.

Fusible (iron-on)

These have heat-activated adhesive on one side. They’re available as tearaway, cutaway or no-show mesh. Fusing stops stretchy or slippery fabrics from moving during hooping. The fabric needs to tolerate the iron.

Heat-away

These are removed with heat rather than water. They’re used for some fabrics that can’t get wet. They’re less common and need the heat method on the packaging, so test before using one on a finished item.

Stabilizer by fabric

Use this as a starting point, and always test on a scrap of the same fabric.

Fabric or item Backing Topper? Notes
T-shirt, jersey No-show mesh or light/medium cutaway, fusible if very stretchy Not usually Never tearaway alone. See our T-shirt embroidery guide
Polo, piqué knit Medium cutaway Often, for small lettering The textured surface can swallow fine detail
Sweatshirt, hoodie Medium cutaway Helpful on thick fleece-backed knits
Fleece, minky Cutaway Yes Don’t press hard with a hot iron
Performance and athletic wear No-show mesh or light cutaway Not usually Watch for hoop marks on shiny fabric
Quilting cotton Medium tearaway; cutaway for dense designs No
Denim, canvas, twill Medium or heavy tearaway; cutaway for dense designs No Bags and totes are often fine with tearaway
Towels, terry Tearaway, or washaway if the back will show Yes
Linen Tearaway or light cutaway No Loose weaves benefit from cutaway
Silk, satin, other delicate wovens Lightweight cutaway or fusible, tested first Sometimes Can show hoop marks. Consider floating
Organza, tulle, chiffon Washaway Sometimes a second film layer
Free-standing lace Heavy fibrous washaway, or several layers of film No No fabric needed
Leather, vinyl Sticky tearaway, fabric floated Sometimes Every needle hole is permanent, so use light, open designs
Velvet, corduroy Sticky or cutaway, fabric floated Yes Hooping crushes the pile
Caps Cap-weight tearaway Sometimes

How design density changes the choice

The same fabric can need different support depending on the design.

  • Light, open designs (outlines, redwork, small lettering) need less. Often one layer of lighter stabilizer is enough.
  • Dense designs (big filled areas, heavy satin work, high stitch counts) need more. Use a heavier stabilizer or two layers, and choose cutaway even on fabrics where tearaway would normally do.
  • On stable fabrics, a dense design on tearaway can perforate the stabilizer and pucker. Switch to cutaway, or add a second layer.

When you use two layers of tearaway, some embroiderers turn them at right angles to each other for more even support.

Weight, color and quality

  • Weight: Stabilizers come in light, medium and heavy weights, and cutaway is often labelled in ounces per square yard. Medium is a reasonable default for many projects. Brands vary, so compare by feel, not just the label.
  • Color: Use white or light stabilizer under light fabrics and black or charcoal under dark ones, so it doesn’t show through or peek out at the edges. No-show mesh is useful where some show-through is likely.
  • Quality: Hold the stabilizer up to the light. It should look even, without thin patches. Uneven stabilizer gives uneven support.

How to use and remove stabilizer

  1. Cut it larger than the hoop, with at least an inch or so to spare on all sides, so the hoop grips it all the way around.
  2. Hoop the fabric and stabilizer together whenever possible. That gives the firmest result. If you need to stick them together first, spray a light mist of temporary adhesive on the stabilizer, not the fabric, away from the machine. Our hooping guide covers the technique.
  3. Float only when needed. For fabric you can’t hoop, hoop the stabilizer and secure the fabric with adhesive stabilizer, spray or a basting box.
  4. Remove it gently afterwards:
    • Tearaway: hold the stitches with one hand while you tear with the other, so you don’t pull the design out of shape. Tear one layer at a time.
    • Cutaway: trim with curved or appliqué scissors, leaving a small margin around the design, roughly a quarter inch, with rounded corners. Don’t cut too close.
    • Washaway: trim the excess first, then rinse or soak, following the product’s instructions.

Common mistakes

  • Using tearaway on knits. The design looks fine at first and distorts after the first wash.
  • Using too little stabilizer for a dense design. This causes puckering and outlines out of register.
  • Using too many layers. A thick stack adds friction and can cause thread breaks and stiffness. Use a heavier single layer instead of a big stack.
  • Skipping the topper on towels. Lettering disappears into the loops.
  • Spraying adhesive on the fabric or near the machine. Residue builds up on the needle and the bobbin area.
  • Not testing. A quick stitch-out on a scrap of the same fabric shows problems before they’re on a finished garment.

For the rest of the setup, our beginner’s guide to using an embroidery machine covers thread, needles and your first stitch-out.

The complete guide to machine embroidery

How to Use an Embroidery Machine: A Beginner's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →