To sew a zipper with a sewing machine, you use a zipper foot: a narrow foot that sits to one side of the needle so you can stitch close to the zipper teeth. For a standard zipper in a seam, the most beginner-friendly method is the centred zipper:
- Machine-baste the zipper opening closed with a long stitch and sew the rest of the seam normally.
- Press the seam allowances open.
- Lay the closed zipper face down over the seam on the wrong side, with the teeth centred on the seam line, and pin or tape it in place.
- With the zipper foot fitted, stitch down one side, across the bottom and up the other side, from the right side of the fabric.
- Unpick the basting stitches to reveal the zipper.
Below you’ll find this method in detail, the method for pouches and bags, a short look at lapped and invisible zippers, and fixes for common problems.
Choose the right zipper
Picking the right zipper makes the job easier:
- Coil (nylon) zippers are flexible and lightweight, and suit most dresses, skirts, cushions and pouches. You can usually sew across the coil carefully and shorten them easily, which makes them a good first choice.
- Metal zippers are sturdier and suit jeans, workwear and heavier bags. You must not sew over the metal teeth or stops, because the needle can break.
- Moulded plastic zippers have chunky individual teeth and are common on jackets, outdoor gear and bags.
- Invisible (concealed) zippers have the coil on the back, so they disappear into the seam. They’re common on dresses and skirts and are best sewn with an invisible zipper foot.
- Separating zippers come fully apart at the bottom, for jackets and cardigans.
For a seam, use the length your pattern specifies. If you can’t find the exact length, buying a coil zipper slightly longer and shortening it is usually easier than making a short one work.
What you need
- Zipper
- Zipper foot for your machine
- Thread to match the fabric (or a contrast, if you want visible topstitching)
- A suitable needle. A universal 80/12 suits many light to medium fabrics; heavier fabrics and metal zippers often call for a 90/14 or larger. Our guide to changing a sewing machine needle covers sizes.
- Pins, sewing clips or double-sided basting tape (wash-away tape or a fabric glue stick also work)
- Iron and pressing cloth
- Seam ripper
- Fusible interfacing strips for lightweight or stretchy fabrics
Set up the zipper foot
Zipper feet differ between machines, so check your manual. The two main designs are:
- Snap-on zipper feet that clip to the presser foot holder on either the left or right side, putting the needle on the opposite edge of the foot. You switch sides depending on which side of the zipper you’re stitching.
- Sliding or adjustable zipper feet that move sideways on a bar or screw, so you can position the needle on either side.
On many modern machines, you can also move the needle position left or right to bring the stitching closer to or further from the teeth.
Whichever type you have, make sure you’re using a straight stitch and that the needle lines up with the notch or edge on the foot. Before sewing, turn the handwheel slowly by hand through a full stitch to check that the needle clears the foot. A needle hitting the foot can break.
Method 1: Centred zipper in a seam
This is the method behind the short answer above. It gives a symmetrical look, with two rows of stitching an equal distance either side of the seam, and suits skirts, cushion covers and centre-back openings.
- Prepare the seam. If the fabric is lightweight, fuse a strip of interfacing along each seam allowance where the zipper will go. Finish the raw edges of the seam allowances with a zigzag or overcast stitch, since they’ll be hard to reach later.
- Baste the zipper opening. Place the fabric right sides together. Mark where the bottom of the zipper opening will be. Sew the opening section with your machine’s longest stitch length (a basting stitch, often around 4 to 5 mm, depending on the machine), without backstitching.
- Sew the rest of the seam. At the bottom mark, switch to a normal stitch length (around 2.5 mm), backstitch to lock it, and sew the remainder of the seam.
- Press the seam open. Press the seam allowances flat and open on the wrong side. A crisp press makes the next steps more accurate.
- Position the zipper. With the fabric wrong side up, place the closed zipper face down on top of the seam allowances. Centre the teeth exactly over the seam line, with the top stop just below the top raw edge’s seam allowance (follow your pattern). Pin, clip or tape it in place along both tapes.
- Baste the zipper (optional but helpful). Hand-baste or machine-baste along each tape to hold it firmly. Many beginners find this gives straighter final stitching.
- Mark your stitching lines. Turn the work right side up. Using chalk or a removable marker, mark lines about 1/4 inch (around 6 mm) either side of the seam line, plus a line across the bottom just below the zipper stop. You can also use narrow tape as a guide.
- Sew the first side. With the zipper foot positioned so the needle is between the foot and the zipper, start at the top and stitch down one side along your line.
- Sew across the bottom. Stop with the needle down at the bottom corner, lift the foot, pivot the fabric and sew across below the zipper stop. On a metal zipper, turn the handwheel by hand here so you don’t hit the stop. Pivot again with the needle down.
- Sew the second side. Stitch up the other side to the top. If your foot needs to switch sides for this, it’s fine to stop, re-fit it, and start the second side from the top instead, which can keep the two sides from twisting in opposite directions.
- Remove the basting. From the right side, carefully cut the basting stitches along the seam line with a seam ripper and pull the threads out. Your zipper is now revealed.
- Press gently, using a pressing cloth and moderate heat, especially on coil and plastic zippers.
For tips on keeping those stitching lines straight and turning the corners crisply, see our guide to sewing a straight line and turning corners.
Method 2: Zipper between two layers (pouches and bags)
Zippered pouches are a popular first zipper project. Here the zipper is usually exposed along the top, with an outer fabric and a lining on each side.
- Prepare the pieces. Cut two outer pieces and two lining pieces the same size. The zipper should be at least as long as the top edge; a longer coil zipper can be trimmed later.
- Make the first sandwich. Lay one outer piece right side up. Place the zipper face down on top, with its tape edge aligned with the top raw edge. Lay one lining piece on top, right side down, aligning its top edge as well. You now have outer (face up), zipper (face down) and lining (face down). Pin or clip through all layers.
- Stitch. With the zipper foot, sew along the top edge through all three layers, close to the teeth but not on them. Move the pull out of the way as needed (see below).
- Fold and press. Fold the outer and lining back so their wrong sides face each other, away from the zipper. Press carefully, keeping the iron away from the coil, or use a pressing cloth.
- Topstitch (optional). Topstitch through the outer and lining close to the fold. This keeps the fabric from catching in the zipper and gives a neater look.
- Repeat on the other side. Make a second sandwich with the remaining outer and lining pieces on the other zipper tape, so the outers face each other and the linings face each other. Stitch, fold, press and topstitch.
- Open the zipper at least halfway. This is easy to forget. If the zipper is closed when you sew the side seams, you won’t be able to turn the pouch right side out.
- Sew the side seams. Unfold so both outers are right sides together on one side and both linings are right sides together on the other, with the zipper teeth folded toward the lining. Sew around the edges, leaving a gap of a few inches in the bottom of the lining for turning. Sew slowly across the ends of a coil zipper; for metal zippers, keep the stops out of the seam allowance.
- Trim and turn. Trim the corners and any excess zipper tape, turn the pouch right side out through the gap, and stitch the gap closed by hand or machine.
Method 3: Lapped zipper (brief)
A lapped zipper has one row of visible stitching, with a fold of fabric from one side covering the zipper like a flap. It’s often used on side seams of skirts and trousers.
In outline, you stitch one zipper tape close to the teeth along the seam allowance on one side. On the other side, the fabric extends a little further and is stitched further from the teeth (often around 3/8 to 1/2 inch, depending on the pattern), so it laps over and hides the zipper. Your pattern instructions will give the exact measurements, so follow those for your first lapped zipper.
Invisible zippers
Invisible zippers are installed differently: they go in before the seam below them is sewn, and the stitching runs right alongside the coil on the back of the zipper so nothing shows from the front.
An invisible zipper foot has grooves underneath that uncurl the coil as you sew, letting the needle stitch right next to it. You can sew one with a standard zipper foot, but it’s harder to get close enough for the zipper to disappear completely. Because the method is quite different, follow your pattern or the zipper packet’s instructions the first time. Our guide to presser feet types explains how the invisible zipper foot differs from a standard one.
Getting past the zipper pull
The slider (pull) is wider than the zipper itself, so stitching straight past it can push your line off course. To avoid this:
- When you’re a couple of inches from the pull, stop with the needle down in the fabric.
- Lift the presser foot.
- Carefully slide the pull past the needle and foot, behind or in front of where you’re stitching. You may need to wiggle the zipper tape gently.
- Lower the foot and continue.
Alternatively, start sewing with the zipper partly open, stop with the needle down before you reach the pull, close the zipper, and then carry on.
Shortening a zipper
Coil zippers are easy to shorten:
- Measure the length you need from the top stop and mark it on the coil.
- Sew a bar tack across the coil at the mark. Use a wide zigzag with a stitch length near zero, sewing several stitches in place, or stitch it by hand with several firm stitches.
- Cut the zipper about 1/2 to 1 inch below the bar tack.
You can also sew the zipper into the project first and trim the excess afterwards, as long as the slider won’t run off the end.
Metal and moulded plastic zippers need the extra teeth removed from the top or bottom, and new stops fitted, which is more fiddly. Buying the correct length is usually simpler for beginners.
Troubleshooting zipper problems
| Problem | Likely cause | What to try |
|---|---|---|
| Stitching wobbles near the pull | Sewing past the slider without moving it | Stop needle-down, lift the foot and slide the pull out of the way |
| Fabric puckers along the zipper | Fabric stretching, or tension too tight | Interface the seam allowances, pin or tape more closely, check top tension |
| Wavy zipper on a knit or bias seam | Seam stretched while sewing | Stabilise with interfacing strips and avoid pulling the fabric |
| Zipper tape shows between fabric folds | Stitching too far from the teeth, or folds not meeting | Baste the seam first so the folds meet over the teeth; stitch a consistent distance |
| Fabric catches in the zipper | Stitching too close to the teeth | Move the needle or foot slightly further away |
| Needle hits the zipper or breaks | Sewing over metal teeth or a stop | Turn the handwheel by hand near stops; keep metal parts out of the stitching line |
| Skipped stitches through thick layers | Needle too small or dull | Fit a fresh, larger needle suitable for the fabric |
| Two sides twisted or uneven | Sewing the sides in opposite directions | Sew both sides in the same direction, from top to bottom |
If the stitches themselves look loose or loopy underneath, the cause is more likely threading or the bobbin than the zipper. Recheck both using our threading guide.
Tips for a neater zipper
- Press at every stage. Pressed seam allowances and folds make it much easier to place a zipper accurately.
- Use basting tape or a glue stick. Holding the zipper flat without pins means nothing shifts as the foot passes.
- Sew slowly. Zippers involve tight spaces and changes in thickness, so a slow, steady speed gives better control.
- Match your stitching distance. Keep the same distance from the teeth on both sides, so the zipper looks centred.
- Practise on scraps. A practice zipper in two pieces of cotton takes only a few minutes and builds confidence before a garment.
- Mind the heat. Coil and plastic zippers can melt under a hot iron, so use a pressing cloth and moderate heat.
Zippers are often one of the first techniques that feels like a leap for new sewists, but with a zipper foot and the basting method they’re very achievable. If you’re still getting comfortable with the machine, our beginner’s guide to using a sewing machine covers the basics to master first.