Fabrics and Needles

How to Sew Vinyl and Oilcloth on a Sewing Machine

Sew clear vinyl, oilcloth, laminated cotton and faux leather on a home machine: needles, stitch length, non-stick feet, clips instead of pins, and fixes for sticking.

On this page
  1. Can you sew vinyl on a regular sewing machine?
  2. Vinyl, oilcloth and laminated cotton: what you’re working with
  3. Needle, thread and stitch settings
  4. Stopping vinyl from sticking to the foot and bed
  5. Holding layers without pins
  6. Cutting and preparing vinyl
  7. Sewing seams step by step
  8. Edges, binding and turning projects right side out
  9. Pressing and storing vinyl
  10. Troubleshooting
  11. Related guides

Can you sew vinyl on a regular sewing machine?

Yes. Most home sewing machines can sew clear vinyl, oilcloth, laminated cotton and lighter faux leathers. You don’t need an industrial machine for typical projects like zipper pouches, tote bags, tablecloths, splash mats and bibs. The changes that matter most are:

  • a sharp needle in a suitable size;
  • a longer stitch length, about 3–4 mm;
  • a way to stop the vinyl sticking to the presser foot and machine bed;
  • clips or tape instead of pins, because holes in vinyl are permanent.

Very thick upholstery or marine vinyl, especially in several layers, can be too much for a lightweight machine. Test on scraps with the same number of layers before starting a project.

Vinyl, oilcloth and laminated cotton: what you’re working with

These materials get grouped together, but they behave a little differently:

  • Clear vinyl is a plastic sheet with no fabric backing. It’s often sold by gauge, and a higher gauge number means a thicker sheet. It sticks the most, shows every needle hole, and gets stiff when cold.
  • Oilcloth, as sold today, is usually a cotton fabric with a PVC coating on one side. The fabric back feeds easily over the feed dogs, while the shiny front can stick to the foot. It’s fairly stiff and creases if folded.
  • Laminated cotton is cotton with a thin, flexible clear coating. It’s softer and drapes better than oilcloth, so it’s often used for bags, bibs and raincoats. It’s usually the easiest of the group to sew.
  • Faux leather and upholstery vinyl have a coated plastic face over a knit or woven backing. Soft, thin versions sew much like laminated cotton. Thick, firm versions need a larger needle and a sturdier machine.

None of these fray, so raw edges can often be left unfinished. None of them recover well from mistakes, because every needle hole stays visible.

Needle, thread and stitch settings

  • Needle: start with a sharp needle, such as a Microtex (sharp) or jeans/denim needle. Size 80/12 suits thin clear vinyl and laminated cotton. Use 90/14 for oilcloth, faux leather and most bag projects, and go up to 100/16 for thicker vinyl or many layers. Some sewists use leather needles on thicker faux leather, but their cutting point slices the material, which can weaken thin vinyl along the seam. A sharp needle is the safer first choice. Start each project with a fresh needle. For other needle types, see our needle sizes and types chart.
  • Thread: a good all-purpose polyester thread. Cotton thread can break under the strain of a stiff material, and it can rot over time on projects that get wet. Heavier topstitching thread can be used in the needle for decorative stitching if your machine handles it, with regular thread in the bobbin.
  • Stitch length: about 3–3.5 mm for most seams, and up to 4 mm for topstitching or thicker vinyl. Short stitches punch a line of closely spaced holes, and the vinyl can tear along it like a perforated sheet.
  • Tension: usually close to your normal setting. Check your sample seam and adjust in small steps if loops show on either side.
  • Speed: slow and steady. Vinyl feeds less predictably than fabric, and going slowly gives you time to correct it before stitches go wrong.

Stopping vinyl from sticking to the foot and bed

Sticking is the most common problem with vinyl. A metal foot grips the plastic face, the material stops moving, and you get tiny stitches, bunching, or skipped stitches. Options, roughly from best to quickest:

  • Non-stick (Teflon-type) foot. This is a white or coated foot that slides over vinyl. It’s inexpensive and worth buying if you sew vinyl more than once.
  • Walking foot. This feeds the top layer along with the bottom layer, which helps when both layers are sticky.
  • Roller foot. This rolls over the surface instead of dragging across it.
  • Matte tape under a regular foot. Stick a piece of matte transparent tape or painter’s tape to the sole of your standard foot, then trim it and cut away the needle opening. This works for a single project.
  • Tissue paper or parchment paper. Lay a strip on top of the vinyl, underneath it, or both, sew through it, then tear it away carefully along the perforations.

If the vinyl sticks to the machine bed or feed dogs rather than the foot, tape a strip of paper over the bed around the needle plate (leaving the feed dogs and needle hole clear), or sew with tissue underneath. With oilcloth, the fabric side usually faces the feed dogs and causes no trouble, so only the coated top needs attention.

Holding layers without pins

Pins leave permanent holes, and on a waterproof project, they leave places for water to get through. Use instead:

  • Sewing clips or small binder clips along the edges.
  • Double-sided basting tape (sometimes called wash-away or wonder tape) inside the seam allowance. Keep it out of the stitching line if you can, because some tapes gum up the needle.
  • Pins inside the seam allowance only, if you must use them, where the holes will be hidden.

Cutting and preparing vinyl

  1. Warm stiff vinyl. Cold vinyl is stiff and can crack at folds. Let it sit at room temperature, or warm it gently with a hair dryer on a low setting before cutting or sewing.
  2. Flatten creases. Unroll the material and let it relax under light weights. Oilcloth creases are hard to remove, so buy and store it rolled where you can.
  3. Mark on the back. Use a pen or chalk on the wrong side of oilcloth and faux leather. For clear vinyl, mark on a removable paper pattern or use washable marker on areas that will be trimmed away.
  4. Cut with a rotary cutter or sharp scissors. Use pattern weights instead of pins. Many clear vinyls come with a tissue paper interleaf; keep it, because it’s handy for sewing.
  5. Sew a test seam with the same layers, needle and stitch length you’ll use on the project.

Sewing seams step by step

  1. Clip or tape the layers together.
  2. Put the needle into the start of the seam by turning the handwheel.
  3. Sew the first few stitches slowly to make sure the material is moving.
  4. Let the machine feed the vinyl. Don’t pull it from behind or push it from the front; that changes the stitch length and can bend or break the needle.
  5. Avoid backstitching where you can. Stitching back over the same spot adds holes close together. Leave long tails, pull them to the wrong side, and tie a knot. On bag seams that take strain, a short backstitch or a second line of stitching a little apart from the first is often used; just keep the extra stitches few and not crowded together.
  6. At corners, stop with the needle down, lift the foot and pivot. Rounded corners are easier than sharp ones in stiff vinyl.
  7. Get it right the first time if possible. Unpicking leaves a line of holes. On clear vinyl, those holes show clearly.

Edges, binding and turning projects right side out

  • Raw edges: vinyl and oilcloth don’t fray, so tablecloths and mats can be left with a straight cut or a pinked edge. Pinking shears give a neat, decorative finish.
  • Binding: bias binding or fabric strips folded over the edge give a clean finish to placemats, bibs and clear pouches. Clip the binding on, then stitch close to its inner edge.
  • Hems: for a turned hem, finger-press the fold or crease it with a bone folder, hold it with clips or tape, and topstitch with a long stitch.
  • Turning right side out: stiff vinyl and oilcloth resist turning. Warm the project with a hair dryer first so it becomes more flexible. Push out corners with a blunt point turner, not scissors, which can puncture the material.
  • Topstitching close to the seam after turning helps seams lie flat, since you can’t press them like fabric.

Pressing and storing vinyl

Vinyl can melt, shrink or stick to a hot iron, and clear vinyl can be ruined by heat. In most cases, it’s better to:

  • finger-press seams, or use a roller or bone folder;
  • if you need heat, test first on a scrap, use a low synthetic setting with no steam, press from the fabric side (on oilcloth or laminated cotton), and use a press cloth.

Store vinyl and oilcloth rolled around a tube, not folded, and away from heat and direct sun. Keep clear vinyl with its tissue interleaf so sheets don’t stick together.

Troubleshooting

Problem Likely cause Fix
Vinyl won’t move, stitches bunch Foot sticking Non-stick, walking or roller foot; tape under the foot; tissue paper
Skipped stitches Dull or wrong needle; vinyl lifting with the needle Fresh sharp needle; try a size larger; walking foot
Seam tears along the stitching Stitch too short Lengthen stitch to 3–4 mm; avoid repeated backstitching
Needle breaks or bends Pulling the material; too many layers; needle too fine Let the machine feed; reduce bulk; larger needle; handwheel over thick spots
Thread breaks or shreds Weak thread; eye too small; needle gummed with tape Polyester thread; larger needle; keep tape out of the stitching line
Cracks at folds Material too cold Warm it gently before sewing or turning
Visible holes from mistakes Unpicking or pins Test on scraps first; use clips; hide pins in the seam allowance

Vinyl shares a lot with leather, but the needle choice differs. See how to sew leather on a home sewing machine for comparison. For heavier bag fabrics, see needles for denim and canvas, and for other awkward materials, see our guide to sewing stretchy and tricky fabrics.

The complete guide to fabrics and needles

Sewing Stretchy and Tricky Fabrics on a Sewing Machine
Read the guide

Keep exploring

Guides from other topics

All topics →