Fabrics and Needles

How to Sew Leather on a Home Sewing Machine

Sew thin garment and craft leather on a domestic machine: choosing leather, leather needles, non-stick or roller feet, stitch length, glued seams and tying off threads.

On this page
  1. Can a home sewing machine sew leather?
  2. Choosing leather for a home machine
  3. Tools and setup
  4. Preparing and cutting
  5. Sewing seams step by step
  6. Seams, topstitching and finishing edges
  7. Ending a seam without backstitching
  8. Troubleshooting
  9. When to use a different machine

Can a home sewing machine sew leather?

Many home sewing machines can sew thin, soft leather, such as the garment-weight lambskin, pigskin and thin cowhide used for clothing, small bags, pouches and appliqué. The usual setup is a leather needle, a foot that won’t stick, a longer stitch and slow, steady sewing.

What home machines generally can’t do well is thick, firm leather, such as the vegetable-tanned tooling leather used for belts, holsters and heavy bags, especially in several layers. Those jobs usually need a heavy-duty or industrial walking-foot machine, or hand stitching. Machines vary a lot, so check your manual and test on scraps before committing to a project.

Choosing leather for a home machine

  • Thickness: leather is often sold by weight in ounces, where 1 oz is roughly 0.4 mm (1/64 inch) of thickness. Thin garment leathers at the lower end of the scale are the easiest on a home machine. Remember that a seam doubles the thickness, and a seam crossing another seam quadruples it.
  • Softness: soft, supple chrome-tanned leathers feed more easily than stiff vegetable-tanned leathers.
  • Finish: leathers with a glossy or tacky finish grip the presser foot more than suede or matte leathers.

For a first project, choose something with few layered seams, such as a simple pouch, a card holder, patches or a lined clutch.

Faux leather and vinyl are different materials and need a different setup. A leather needle’s cutting point can weaken them. See how to sew vinyl and oilcloth for those.

Tools and setup

  • Needle: a leather needle, which has a cutting point that slices a clean hole rather than pushing fibres aside. Sizes 80/12–90/14 suit thin, soft leathers, and 100/16 suits slightly heavier ones or multiple layers, if your machine allows it. Use a fresh needle for each project.

  • Thread: a strong polyester thread. A heavier “upholstery” or bonded nylon or polyester thread is often used for visible topstitching on bags, if your machine and needle size can handle it. Avoid cotton thread, which can weaken and break.

  • Presser foot: standard metal feet often stick to the top of leather. Options include:

    • a non-stick (Teflon-type) foot, which glides over the surface;
    • a roller foot, which rolls over the leather;
    • a walking foot, which feeds the top layer along with the bottom.

    In a pinch, a strip of matte tape on the underside of a regular foot, or tissue paper over the leather, reduces sticking.

  • Stitch length: longer than normal, about 3–4 mm. Short stitches perforate leather like a postage stamp and can make it tear along the seam.

  • Clips and tape, not pins: pin holes in leather are permanent. Use sewing clips, binder clips or double-sided basting tape. Leather glue suited to sewing can be used too, but avoid gluing exactly where the needle will go, because glue can gum up the needle.

Preparing and cutting

  1. Check the hide for flaws, such as scars and thin spots, and plan pattern pieces around them.
  2. Trace on the wrong side with a pen, chalk or silver marker. Don’t pin pattern pieces; use weights.
  3. Cut with a sharp rotary cutter on a mat, or with sharp shears. A clean edge matters because leather edges often show.
  4. Test on scraps: sew a sample seam with the same number of layers, and check stitch length, tension and feeding.

Sewing seams step by step

  1. Clip or tape the layers together.
  2. Lower the needle by hand into the start of the seam.
  3. Turn the handwheel for the first few stitches to confirm the needle penetrates cleanly and the leather feeds.
  4. Sew slowly and evenly. Let the machine feed the leather. Pulling or pushing will distort stitch length and can bend the needle.
  5. Don’t unpick and re-sew if you can avoid it. The original holes will stay visible. Get the seam right on a test piece first.
  6. Pivot carefully at corners with the needle down. Avoid tiny stitches at corners, which weaken the leather.

Seams, topstitching and finishing edges

  • Open seams: after sewing, finger-press the allowances open, apply a thin layer of leather glue under each, and tap flat with a mallet or hammer, protecting the surface with a scrap.
  • Topstitching: topstitching on each side of the seam holds allowances flat and gives a crisp, professional look. Use a longer stitch and stitch from the right side.
  • Lapped seams: overlap one edge on another and stitch through both. Leather doesn’t fray, so this is less bulky than a traditional seam.
  • Raw edges: leather doesn’t fray, so edges can be left raw, or finished with edge paint or burnishing, depending on the leather.
  • Pressing: if you must press, use a low heat, a dry iron and a press cloth (or brown paper). Test first, because heat and steam can mark or shrink leather.

Ending a seam without backstitching

Backstitching on leather punches extra holes close together and can weaken the end of a seam. Instead:

  1. Leave long thread tails at the start and end of the seam.
  2. Pull the top thread through to the wrong side (tug the bobbin thread and the top thread loop will appear).
  3. Tie the two threads in a secure knot.
  4. Add a tiny dab of glue or seam sealant if you like, and trim.

Troubleshooting

Problem Likely cause Fix
Leather won’t feed / stitches bunch up Foot sticking Non-stick, roller or walking foot; tissue paper; tape under the foot
Skipped stitches Dull or wrong needle; leather lifting with the needle New leather needle; check needle size; walking foot
Needle breaks Too many layers; pulling the leather; needle too fine Reduce bulk; larger needle; hand-crank over thick spots
Seam tears along the stitching Stitch too short Lengthen to 3–4 mm
Thread shreds Needle eye too small for the thread Larger needle or a lighter thread
Motor strains Leather too thick for the machine Thinner leather, fewer layers; consider a heavy-duty machine

When to use a different machine

Consider hand stitching, a heavy-duty walking-foot machine, or an industrial leather machine if:

  • you want to sew firm, thick leather or many layers on a regular basis;
  • you need heavy bonded thread for strong bag or saddlery seams;
  • your home machine repeatedly breaks needles or strains, even with thin leather and the right setup.

Pushing a household machine beyond its limits can throw out its timing or damage the motor.

For needle choices on other heavy fabrics, see needles for denim and canvas and the needle sizes and types chart. For other awkward fabrics, see our guide to sewing stretchy and tricky fabrics.

The complete guide to fabrics and needles

Sewing Stretchy and Tricky Fabrics on a Sewing Machine
Read the guide

Keep exploring

Guides from other topics

All topics →