Machine Embroidery

Embroidery Machine Troubleshooting: Thread Breaks, Bunching and Bobbin Showing

Fix embroidery machine thread breaks, bird nests under the fabric, and bobbin thread showing on top, with a quick reset, tension tests, and fixes by cause.

On this page
  1. Start with the five-minute reset
  2. Thread keeps breaking
  3. Thread bunching underneath (bird nesting)
  4. Bobbin thread showing on top
  5. How to tell if your embroidery tension is correct
  6. What the bobbin does on an embroidery machine
  7. Winding bobbins for embroidery
  8. When to call a technician

Start with the five-minute reset

Thread breaks, bird nests and bobbin thread showing look like different problems, but many have the same small set of causes. Before changing any tension settings, do this reset in order. It fixes a large share of problems on its own.

  1. Rethread the top completely with the presser foot raised. Raising the foot opens the tension discs so the thread can seat between them. Follow every guide, and make sure the thread goes through the take-up lever.
  2. Put in a new embroidery needle, the right way around and pushed fully up into the clamp. A needle that looks fine can still have a burr or a dull point.
  3. Take out the bobbin and clean the area. Brush lint from the bobbin case, from under the tension spring, and from the hook race, following your manual. Turn the machine off before you reach in.
  4. Reinsert the bobbin so it unwinds in the direction your manual shows, and make sure the thread is pulled fully into the tension slot or under the spring.
  5. Check the hoop. The fabric should be smooth and firm, the hoop locked onto the carriage, and the stabilizer suited to the fabric.

Stitch a test. If the problem is still there, use the section below that matches what you see.

Thread keeps breaking

First, look at the broken end:

  • Frayed or shredded end: usually friction. Look at the needle (worn, burred or too small an eye), burrs on the needle plate or hook, or the thread catching somewhere along its path.
  • Clean snap: usually too much tension or a snag. Look at the top tension, the spool catching on its cap or notch, or thread wrapped around the spool pin.
Cause Fix
Worn, bent or burred needle Replace with a fresh 75/11 embroidery needle. Use a larger or metallic/topstitch needle for metallic or thicker threads
Needle inserted wrong Reinsert flat side to the back (on most home machines) and push it fully up
Thread snagging at the spool Use a spool cap the right size, turn the spool so its notch isn’t catching the thread, or move cross-wound spools and cones to a thread stand
Top tension too tight Rethread first, then lower top tension a step at a time
Old or brittle thread Test a fresh spool of the same color
Burr on the needle plate or hook (often after a needle strike) Run a fingernail around the needle hole to feel for a nick. A damaged plate may need replacing; have hook damage checked by a technician
Lint packed in the bobbin area Clean it out
Very dense design, or many layers stitched over one spot Slow the machine down. If one design breaks constantly on a well-tuned machine, the file may be poorly digitized
Spray adhesive gumming the needle Spray the stabilizer, not the fabric, and lightly. Replace the gummed needle
Machine running too fast for the thread Reduce speed, especially for metallic, rayon and small lettering

How do I stop thread breaking in general? Most breaks are prevented by changing needles regularly, using decent thread fed from the right kind of spool pin, keeping the bobbin area clean, and slowing down for hard designs.

Thread bunching underneath (bird nesting)

A thick tangle of thread under the fabric, or wrapped around the bobbin area, is called a bird’s nest. It’s usually a top-thread problem, not a bobbin problem. When the top thread has no tension, the hook pulls loop after loop of loose thread underneath.

The common causes:

  • The machine was threaded with the presser foot down, so the thread never went between the tension discs.
  • The thread missed the take-up lever.
  • The top thread tail was pulled underneath at the start. Holding the tail lightly for the first few stitches, if your manual recommends it, helps prevent this.
  • The fabric is flagging, bouncing up and down with the needle, because the hooping is loose or there isn’t enough stabilizer.
  • Lint or a thread scrap is caught in the bobbin case or hook race.
  • The bobbin was inserted the wrong way, or isn’t seated properly.

To clear a nest safely:

  1. Stop the machine and turn it off.
  2. Don’t yank the hoop or the fabric. That can bend the needle or knock the timing out.
  3. Raise the needle with the handwheel if your manual allows it, then cut the threads between the fabric and the machine from underneath with small scissors.
  4. Remove the hoop carefully, take out the bobbin case, and pick out every scrap of thread from the hook area.
  5. Replace the needle, rethread with the foot up, and test.

You can sometimes save the project by picking the nest off the back and restarting the design a few stitches before the problem. Many machines let you step back through stitches.

Bobbin thread showing on top

On a good stitch-out, the top thread pulls a little of itself to the back, and the bobbin thread never shows on the front. White bobbin thread dotting the top of a design, especially along the edges of satin stitches, means the balance has tipped. Either the top thread is pulling too hard, or the bobbin thread is too loose.

Work through these fixes in order, from easiest to most invasive:

  1. Rethread the top with the foot up. A thread caught outside a guide or wrapped around the spool pin adds tension and drags the bobbin thread up.
  2. Check the bobbin. It should be inserted the right way, fully seated, with the thread drawn under the tension spring.
  3. Clean under the bobbin tension spring. Lint trapped there loosens the bobbin tension.
  4. Use embroidery bobbin thread. Switching bobbin brands or weights can change the balance.
  5. Make sure the fabric isn’t flagging. Firm hooping and enough stabilizer matter here too.
  6. Lower the top tension slightly if your machine lets you adjust it in embroidery mode.
  7. Adjust bobbin tension last, and only if your manual says you can. On machines with an adjustable bobbin case, first mark the screw’s current position with a fine marker. Then turn it in very small increments, roughly an eighth of a turn at a time, clockwise to tighten. Test after each change.

Some designs bring up a little bobbin thread no matter what. Very small satin lettering and tight curves are the usual examples. A design with that problem on several machines may need lighter density or wider columns.

How to tell if your embroidery tension is correct

The most common check is to look at the back of a satin column. Many embroiderers stitch a test letter like “I” or “H”, or a word with columns at different angles, in a contrasting top color on two layers of medium cutaway. Then they turn it over:

  • Balanced: the bobbin thread makes up roughly the center third of the column, with top thread visible on each side.
  • Bobbin too tight, or top too loose: little or no bobbin thread is visible, and top thread covers the whole back. This may come with loops on top.
  • Bobbin too loose, or top too tight: the bobbin thread covers most of the back and starts appearing on the front.

What tension number should my machine be on? There’s no universal number. Dials and screens use different scales on different brands, many machines set tension automatically in embroidery mode, and the right setting depends on the thread, fabric and design. Use the test stitch to judge, not a number.

What the bobbin does on an embroidery machine

Like a sewing machine, an embroidery machine forms a lockstitch. The needle carries the top thread down, the rotating hook catches a loop of it, and the loop wraps around the bobbin thread before the take-up lever pulls it back up tight. The bobbin thread stays on the back as the anchor for every stitch. In embroidery, the goal is for that interlock to sit slightly underneath the fabric, which is why bobbin thread is lighter and why bobbin tension matters so much.

Winding bobbins for embroidery

Most of the time, you don’t wind your top embroidery thread onto bobbins. Dedicated bobbin thread, or prewound bobbins if your machine accepts them, gives more consistent results. The exception is a project where the back will show, such as free-standing lace or some towels. In those cases, a bobbin in the same color, often the same thread, makes the item look good on both sides.

When you wind your own bobbins:

  • Wind at a moderate speed so the thread lays on evenly.
  • Don’t overfill. An overfilled bobbin can drag or fail to seat.
  • Use the bobbins designed for your machine. Bobbins that look similar can differ slightly in size and cause tension problems.

When to call a technician

Stop troubleshooting and book a service if:

  • The machine skips or won’t form stitches even after the full reset (see why your embroidery machine skips stitches and why it may not stitch at all).
  • Problems started right after a needle hit the hoop, or after a nest that jammed the machine. These can knock the hook timing out.
  • You hear grinding, knocking or new noises.
  • You find nicks in the hook or bobbin case.

Take your test stitch-out to the shop with you. It helps the technician see the problem.

For prevention, the basics cover most of it: choose the right stabilizer, hoop firmly without stretching, and use thread that runs well in your machine (see our thread brand comparison).

The complete guide to machine embroidery

How to Use an Embroidery Machine: A Beginner's Guide
Read the guide

Keep exploring

Guides from other topics

All topics →