The short version
To machine embroider a T-shirt without stretching or puckering:
- Use cutaway stabilizer, either no-show mesh or a light to medium cutaway. Fusible is best. Never use tearaway on its own.
- Fit a ballpoint embroidery needle, commonly 75/11.
- Hoop the shirt without stretching it. Let the stabilizer provide the firmness.
- Choose a lighter design, avoiding big, dense filled areas.
- Keep the rest of the shirt out of the way of the needle.
- Trim the stabilizer neatly afterwards, and wash the shirt inside out.
The details below explain each step.
Why T-shirts stretch and pucker
T-shirt fabric is a knit, made of interlocking loops. That’s what makes it stretchy and comfortable, and also what makes it tricky to embroider:
- It stretches in the hoop. If you pull it taut, it’s stitched while stretched. When you unhoop it, the fabric relaxes and the design puckers.
- It moves under the needle. Each stitch pulls on the fabric. Without firm support, the design shrinks inward, outlines drift away from fills, and the knit can flag (bounce), which causes skipped stitches.
- It needs support for life. A T-shirt is stretched every time it’s worn or washed, so the stitches need permanent backing, not just support while stitching.
What you need
- A T-shirt, ideally pre-washed (see below)
- Cutaway stabilizer: no-show/poly mesh for light-colored and lightweight tees, or light to medium cutaway for heavier tees and denser designs. Fusible versions are helpful.
- Ballpoint embroidery needles, commonly 75/11
- 40-weight embroidery thread and bobbin thread
- A hoop that fits the design, as small as possible
- A removable fabric marker, ruler and the hoop’s template
- Optional: temporary spray adhesive, clips, a soft fusible backing to cover the stitches inside
Choose the shirt and the design
The shirt: Medium-weight and heavier cotton or cotton-blend tees are easier than thin, very stretchy or slinky ones. A tightly knitted tee holds stitches better than a loose, open knit. If you’re practicing, start with an inexpensive plain tee in a fabric like the one you plan to use.
The design: Designs made for knits stitch best on T-shirts. Look for:
- Lighter density, open or light-fill designs, outlines, redwork and moderate satin lettering
- Reasonable size for the placement. Left-chest designs are often around 3 to 4 inches wide for adults
Be cautious with:
- Large, dense filled areas like solid patches of fill or big block logos. They’re heavy, stiff and prone to puckering on thin knits.
- Tiny lettering, which can sink into the knit.
Prep the shirt
- Pre-wash and dry it, as you will after finishing. This removes sizing and lets the shirt shrink before you embroider rather than after. Skip fabric softener, which can affect fusible stabilizers.
- Press it flat by lifting and pressing, not dragging the iron, so you don’t stretch the knit.
Mark the placement
Put the shirt on, or lay it flat, and mark the center of the design with crosshairs using a removable marker. Rough starting points for adult tees:
- Left chest: the design center is often placed several inches below the shoulder seam (commonly around 7 to 9 inches down from where the shoulder meets the collar) and around 3 to 4 inches from the center front. It’s the wearer’s left.
- Center front: the top of the design is often placed around 3 to 4 inches below the neckline. That’s roughly a hand’s width, depending on design height and shirt size.
These are only guidelines. Hold a paper printout of the design against the shirt, or try the shirt on with the printout, to check before hooping. Line up the vertical crosshair with the shirt’s center fold, or with the grain of the knit, so the design isn’t crooked.
Stabilize and hoop
1. Cut the stabilizer larger than your hoop on all sides.
2. Fuse or stick it to the inside of the shirt. Fusing no-show mesh to the back of the design area, following the product’s heat instructions, stops the knit from shifting and stretching while you hoop. If you’re not using fusible, a light mist of temporary adhesive on the stabilizer (not the shirt) does a similar job.
3. Hoop the shirt and stabilizer together, relaxed.
- Turn the shirt so you can slide the outer ring inside the shirt, under the front only. Or use a hooping aid.
- Lay the front smooth over it, line up the template with your crosshairs, and press the inner ring in evenly.
- Don’t pull the fabric to tighten it. The fused stabilizer provides the firmness. If you see the knit’s ribs bending or the fabric looks stretched, unhoop and try again.
- The surface should be smooth and firm, but the knit should look exactly as it does flat.
Our hooping guide covers the technique, and how to avoid hoop marks.
Alternative: float the shirt. Hoop the cutaway alone, spray it lightly or use a sticky stabilizer, smooth the shirt on top, and stitch a basting box around the design first. Floating avoids hoop marks. Fabric can move more, though, so use it with lighter designs.
Topper: Smooth jersey usually doesn’t need one. For textured knits like waffle or slub, a water-soluble topper helps small details stay crisp.
Set up the machine and stitch
- Fit a new ballpoint needle. A ballpoint pushes between the knit’s loops rather than piercing them, which reduces holes, runs and skipped stitches.
- Check the bobbin and thread the top with the presser foot up.
- Load the design and make sure it’s oriented correctly. Many people turn the shirt so the neckline is at the top of the hoop or toward the machine arm. Check the screen preview and rotate the design if needed.
- Keep the rest of the shirt out of the way. Roll or fold the back, sleeves and hem away from the hoop and clip them, so they can’t slide under the hoop or get stitched to the front. Check underneath before you start, and again during the first color.
- Trace the design outline, if your machine can, to confirm it fits the hoop and doesn’t come near the frame.
- Consider slowing down. A lower speed reduces flagging and thread problems on knits.
- Stay nearby, especially during the first few hundred stitches, so you can stop quickly if fabric gets caught.
Finishing
- Remove the hoop, then unhoop. Clip jump threads close to the fabric with curved embroidery scissors.
- Trim the cutaway from inside the shirt, leaving a margin of roughly a quarter to half an inch around the design. Round the corners so they don’t poke through or show as sharp lines. Lift the stabilizer away from the shirt as you cut, so you don’t snip the shirt.
- Press from the back with a pressing cloth, using a temperature suited to the fabric and thread. Avoid pressing hard directly on the stitches, which flattens them.
- Optional: add a soft cover. A soft fusible backing ironed over the back of the stitches covers scratchy stitches and stabilizer. That’s helpful for children’s clothes and sensitive skin.
Fixing common T-shirt problems
| Problem | Likely cause | Fix next time |
|---|---|---|
| Puckers around the design | Shirt stretched in the hoop, too little stabilizer, design too dense | Hoop relaxed, fuse cutaway, use a lighter design |
| Design looks wavy after washing | Tearaway used, or the stabilizer too light | Use cutaway or no-show mesh, a heavier weight for denser designs |
| Outlines don’t line up with fills | Knit shifted during stitching | Fuse the stabilizer, hoop more firmly (without stretching), slow down |
| Holes or runs around stitches | Sharp or worn needle, design too dense | New ballpoint needle, lighter density |
| Skipped stitches | Flagging, needle | Firmer support, new ballpoint needle |
| Back of the shirt stitched to the front | Excess fabric slid under the hoop | Roll and clip the excess, check underneath before starting |
| Hoop marks | Hoop too tight, shirt left hooped | Loosen the screw setting, unhoop promptly, or float |
| Stabilizer shows through a light tee | Heavy or white cutaway under a thin shirt | Use no-show mesh in a matching or skin tone where available |
Mild puckering can sometimes be eased by pressing from the back with steam and gently patting the fabric flat. Severe puckering usually means the design needs to be stitched again with better stabilization.
Washing and care
- Wash inside out in cool or warm water on a gentle cycle.
- Avoid chlorine bleach unless you know the thread is bleach-safe. Many polyester embroidery threads tolerate more than rayon. See our embroidery thread brand comparison.
- Tumble dry low or air-dry, and don’t leave it in a hot dryer for long.
- Iron from the back, never directly on the stitches.
For choosing stabilizers on other fabrics, see which stabilizer to use for every fabric. If you plan to sell personalized shirts, our article on whether owning an embroidery machine is profitable covers the business side.