The short answer
An embroidery machine skips a stitch when the hook under the needle plate misses the loop of top thread the needle makes. Normally, as the needle starts to rise, the top thread forms a small loop beside it, and the hook catches that loop and wraps it around the bobbin thread. If the loop is too small, in the wrong place, or there when the hook goes by, no stitch forms.
On home embroidery machines, the usual causes are:
- A worn, bent or wrongly inserted needle
- Fabric “flagging”, which means bouncing up and down with the needle because the hooping or stabilizer isn’t firm enough
- Threading problems or thread that doesn’t run smoothly
- Lint or thread scraps in the bobbin and hook area
Timing problems, where the hook and needle fall out of sync, are less common. When they happen, though, they usually need a technician.
What skipped stitches look like
Skipped stitches aren’t always obvious at first. Look for:
- Run stitches and outlines: a stitch that’s two or three times longer than its neighbours, or a gap in an outline.
- Satin stitches: top thread lying loose across the surface, small gaps in the column, or loops that pull out easily.
- Fills: odd long stitches that catch on a fingernail.
Skipping is different from these related problems:
- Thread breaking. The machine usually stops, and the thread is snapped or shredded. See our guide to thread breaks, bunching and bobbin showing.
- Bobbin thread showing on top. That’s a tension balance problem, covered in the same guide.
- No stitches forming at all. The needle goes up and down but nothing locks. That’s covered in why your embroidery machine may not be stitching.
Check these first, in order
Work through these from easiest to hardest, and test after each one. Turn the machine off before you reach into the needle or bobbin area.
1. Replace the needle
This fixes more skipped stitches than anything else. A needle can look perfect and still have a dull point, a slight bend, or a burr from hitting a pin or the hoop.
- Use an embroidery needle, commonly size 75/11 for standard 40-weight embroidery thread. Embroidery needles have a larger eye and a shape that helps the thread form a good loop.
- Push the needle fully up into the clamp, with the flat side facing the back on most home machines. Check your manual. A needle that sits even slightly low or turned can throw off the loop.
- Many embroiderers replace the needle roughly every 8 hours of stitching, or at the start of each new project. Replace it right away after it hits anything.
2. Stop the fabric flagging
If the fabric lifts with the needle on each stitch, the loop can’t form where the hook expects it. Flagging is very common with loose hooping, thin stabilizer, and fabric that’s floated rather than hooped.
- Hoop fabric and stabilizer together so they’re smooth and firm, but not stretched. Our hooping guide covers the technique.
- Use the right type and weight of stabilizer for the fabric. See which stabilizer to use for every fabric.
- If you float fabric on a hooped stabilizer, add a basting box around the design so it can’t lift.
- Check that the hoop is fully locked onto the embroidery arm or carriage.
3. Rethread the top with the presser foot up
Raise the presser foot (or embroidery foot lever) before threading so the tension discs open and the thread can seat between them. Follow every guide, make sure the thread passes through the take-up lever, and check that it isn’t wrapped around the spool pin or catching on the spool’s notch.
4. Clean the bobbin and hook area
Remove the needle plate and bobbin case if your manual says you can. Then brush out lint and pick out any thread scraps. Lint packed into the hook race can stop the hook from moving smoothly past the needle. Oil only if your manual says to, and only where it says.
5. Check the bobbin
Use the bobbin type made for your machine. Insert it so it unwinds in the direction your manual shows, and pull the thread fully into the tension slot. An overfilled or unevenly wound bobbin can cause problems as well.
Less obvious causes
If the five checks above don’t solve it, look through these:
| Cause | What to do |
|---|---|
| Adhesive on the needle from spray or sticky stabilizer | Wipe or replace the needle. Spray the stabilizer lightly, never the fabric, and keep spray away from the machine |
| Needle too small for the thread | Metallic, 30-weight and other thicker threads often need a larger or metallic-type needle |
| Old, dry or poor-quality thread | Test with a fresh spool. Our thread brand comparison covers threads that run well |
| Stitching too fast | Slow the machine down, especially for metallic thread, small lettering and dense areas |
| Thick seams or bulky layers | The needle can deflect on thick seams. Avoid placing designs over seams, and use a larger needle for heavy fabric |
| Embroidery foot set too high | Some machines let you adjust embroidery foot height. If it sits too high above thick fabric, the fabric can flag. Check your manual |
| Design problems | Very short stitches, or many stitches piled on one spot, can skip even on a well-tuned machine. If one design skips and others don’t, the file may be the problem |
| Damaged needle plate or hook | A nick from a needle strike can catch the thread. Have hook damage checked by a technician |
Skipped stitches on knits and stretchy fabric
T-shirts, jersey and performance knits are especially prone to skipped stitches. The fabric stretches and lifts with the needle, and a sharp needle can push between the fibres without forming a clean loop.
- Try a ballpoint embroidery needle (sometimes labelled “embroidery ballpoint” or similar).
- Use a cutaway stabilizer, and consider a fusible one to stop the knit from moving.
- Don’t stretch the fabric when you hoop it.
Our guide to machine embroidering a T-shirt goes through the whole setup.
When it’s a timing problem
The timing between the needle and the hook is set at the factory. A hard jolt can knock it out, usually a needle hitting the hoop or a bad bird’s nest that jams the machine. Signs that timing may be the issue:
- Skipping started right after a needle strike or jam.
- It continues with a new needle, fresh thread, clean bobbin area and firm hooping.
- It happens on every fabric and every design, sometimes with new clicking or knocking sounds.
Adjusting timing usually means removing covers and setting the hook position precisely. On most home machines, this is a job for a qualified technician rather than something to try at home. Take a test stitch-out with you to show the problem.
How to prevent skipped stitches
- Change needles regularly and right after any strike.
- Hoop firmly, and match the stabilizer to the fabric and the design’s density.
- Always thread with the presser foot up.
- Clean lint out of the bobbin area often. Many owners do it with every bobbin change or two.
- Slow down for difficult threads and designs.
- Stitch a test of new designs on similar fabric first.
If you’re new to all this, our beginner’s guide to using an embroidery machine covers the setup habits that prevent most stitch problems.