The short answer
When an embroidery machine runs but doesn’t stitch, the top thread usually isn’t catching the bobbin thread. The most common reasons are threading done with the presser foot down, a bobbin inserted the wrong way, or a needle that’s damaged or not pushed fully up.
When the machine won’t run at all, it’s often a safety interlock rather than a fault. The foot lever is up, the hoop isn’t attached, or the bobbin winder is still engaged, and the machine is refusing to start until that’s fixed.
Start by working out which of those you’re dealing with, because the fixes are different.
First, work out which problem you have
| What you see | Most likely area | Jump to |
|---|---|---|
| Start button does nothing, or an error message appears | Interlock or setup | Won’t start at all |
| Needle goes up and down, hoop moves, but no stitches lock into the fabric | Threading, bobbin or needle | No stitches form |
| Stitches a little, then stops | Color change, thread sensor or bobbin | Stitches, then stops |
| Design won’t open, or the machine says it’s too big | File or hoop size | Design won’t load |
Read the screen message first if there is one. Most machines show a specific message, and the troubleshooting or error table in your manual will tell you what it means.
If the machine won’t start at all
Common reasons a machine refuses to start embroidering:
- The presser foot or embroidery foot lever is up. Many machines won’t stitch with the foot raised and will show a reminder.
- The hoop isn’t attached or locked. Slide it onto the embroidery arm or carriage until it clicks or locks, following your manual.
- The selected hoop doesn’t match. Some machines check the hoop size and won’t stitch if the design needs a bigger hoop than the one attached.
- The embroidery unit isn’t attached properly, or can’t move. On many machines, the unit moves to a starting position when you switch it on. Make sure nothing is blocking the arm or carriage and that there’s clear space around the machine.
- The bobbin winder is still engaged. On some machines, leaving the winder spindle in the winding position stops stitching.
- The top thread sensor doesn’t detect thread. If the machine thinks the top thread is missing or broken, it won’t start. Rethread fully.
- The wrong foot is on. Combination machines usually need the embroidery foot fitted for embroidery mode.
- A lock or needle-change mode is on. Some machines have a key that locks the controls while you change the needle or foot. Check the screen for a lock symbol.
If none of these applies, turn the machine off, wait a moment, and turn it back on. That clears temporary errors on some computerized machines.
If the needle moves but no stitches form
This means the hook isn’t catching a loop of top thread. Turn the machine off before working near the needle or bobbin, then check:
- Rethread the top with the presser foot up. Raising the foot opens the tension discs. If the thread isn’t seated between them, or misses the take-up lever, stitches won’t form properly.
- Check that the thread is actually through the needle eye. Automatic needle threaders sometimes leave a loop behind the needle instead of through it.
- Check the bobbin. Is there thread on it? Is it the correct bobbin for your machine, inserted so it unwinds in the direction your manual shows, with the thread pulled into the tension slot or under the spring?
- Replace the needle. A bent needle, one put in backwards, or one not pushed fully up into the clamp can miss the hook completely. On most home machines, the flat side of the shank faces the back.
- Check the needle type. Home machines generally use the standard household needle system (often marked 130/705 H). Many multi-needle commercial machines use a different system. A needle that fits the clamp but isn’t the right system won’t sit at the right height.
- Leave a longer thread tail. If the tail is very short, the first stitch can pull the thread straight out of the needle. Follow your manual on whether to hold the tail for the first few stitches.
- Clean out the bobbin area. Packed lint or a scrap of thread in the hook race can stop stitches from forming.
If stitches form but some are missing here and there, that’s a different problem. See why embroidery machines skip stitches.
If it stitches a little, then stops
Before assuming something’s wrong, check the screen:
- It’s a color change. The machine stops at the end of each color so you can rethread. Beginners often mistake this for a fault. The screen usually shows the next color.
- It’s a planned stop. Appliqué designs often include stops for placing and trimming fabric.
If it’s neither:
- The top thread broke or came out of the needle. The thread sensor stops the machine. Rethread, and find out why it broke. Our guide to thread breaks, bunching and bobbin showing covers this.
- The bobbin is running low. Many machines warn you and stop.
- The thread is snagging at the spool. A thread caught on the spool notch or wrapped around the spool pin can trip the sensor.
- A bird’s nest has formed underneath. Stop, turn the machine off, and cut the tangle free. Don’t pull the hoop out.
- The machine is straining. Very dense designs or thick, bulky items can make some machines stop to protect the motor. Slow down, or check whether the item is too thick for your machine.
If the design won’t load or won’t start
- The file format isn’t supported. Embroidery machines read specific stitch file formats, not images like JPG or PNG. Check which formats your machine reads, and see our guide to embroidery file formats.
- The design is bigger than the hoop or the machine’s maximum embroidery area. Use a larger hoop if your machine takes one, or choose a smaller version of the design. Shrinking a stitch file a lot on the machine can cause density problems.
- The file is still zipped. Unzip downloaded designs on your computer before copying them to a USB stick.
- The USB stick isn’t readable. Some machines are fussy about stick size or formatting. Try a smaller, simply formatted stick with only a few files on it, and check your manual’s requirements.
- The file is damaged. Re-download it or try another design to rule this out.
A quick reset that fixes most cases
If you’re not sure where the problem is, do all of this in order:
- Turn the machine off.
- Remove the needle and fit a fresh embroidery needle, fully up, facing the right way.
- Take out the bobbin, clean the bobbin area, and reinsert the bobbin correctly.
- Raise the presser foot and rethread the top completely.
- Check the hoop is attached and locked and that nothing blocks the embroidery arm.
- Turn the machine on, choose a simple built-in design, and test on scrap fabric with stabilizer.
If the built-in design stitches but your own design doesn’t, the problem is the file, not the machine.
When to call a technician
Book a service if:
- The machine still won’t form stitches after the full reset.
- The problem started right after a needle hit the hoop or a nest jammed the machine. Either can knock the timing between the needle and hook out of alignment.
- You hear grinding, knocking or other new noises.
- The same error message keeps coming back and your manual doesn’t explain it.
Resetting timing usually means opening the machine, so on most home machines it’s a technician’s job. Take a test sample and a note of any error messages with you.
New to the machine? Our beginner’s guide to using an embroidery machine covers the setup steps that prevent most of these problems.