Lettuce hems vs gathered ruffles
Both give a wavy, frilly edge, but they work in different ways:
- A lettuce hem stretches the edge of a knit fabric while a dense zigzag sews over it. The thread locks the edge in its stretched state, so when you let go it ripples like a lettuce leaf. There’s no extra fabric involved.
- A gathered ruffle takes a strip of fabric that’s longer than the edge it’s sewn to and compresses it with gathering stitches. It works on wovens and knits.
There’s no single built-in “ruffle stitch” on most sewing machines. Both effects come from ordinary stitches combined with technique, or from a dedicated foot or attachment.
Which fabrics work for a lettuce hem
Lettuce hems rely on stretch, so you can’t lettuce every fabric:
- Works well: cotton/spandex jersey, rib knit, lightweight interlock, stretch mesh, many rayon or viscose jerseys. Fabrics with good stretch and good recovery give the most ripple.
- Works less well: thick or stable knits like ponte, sweatshirt fleece and double knit. They stretch too little to ruffle much.
- Doesn’t really work: woven fabrics cut on the straight grain. A woven cut on the bias stretches a little and can give a soft wave, but not the full effect.
Sew the hem along the direction of greatest stretch. On most jersey that’s across the width of the fabric, which is usually how hems on tops and skirts run anyway. Always test on a scrap to see how much ripple you get.
Machine settings for a lettuce hem
Starting points (your machine and fabric may need tweaking):
- Stitch: zigzag
- Width: medium, about 2.5–4 mm. Wider gives a bolder edge.
- Length: very short, about 0.5–1 mm, so the stitches nearly touch (close to satin stitch)
- Needle: jersey/ballpoint or stretch, 75/11 or 80/12
- Thread: all-purpose polyester; matching for a subtle edge, contrasting for a decorative one
- Foot: standard zigzag foot, or a satin stitch foot (open toe or grooved underneath) if you have one, so the dense stitching doesn’t jam
- Tension: start at default; reduce the upper tension slightly if the edge puckers rather than ripples
Method 1: raw-edge lettuce hem
This is the quickest version, and the one most often used on T-shirt sleeves and baby clothes.
- Trim the edge cleanly. Many knits don’t fray, so a raw edge is fine.
- Place the fabric right side up with the edge under the foot. Position it so the left swing of the needle goes into the fabric and the right swing falls just off the edge, so the thread wraps around it.
- Lower the needle into the fabric and sew a few stitches without stretching to anchor the thread.
- Stretch as you sew. Hold the fabric in front of and behind the foot, and stretch it evenly as it feeds. The more you stretch, the more it will ripple. Let the feed dogs move the fabric. Your hands supply the stretch, not the forward pull.
- Sew at a slow, steady speed and reposition your hands every few inches.
- Release and check. Steam lightly, without pressing flat, to help the edge settle.
Method 2: folded-edge lettuce hem
This version is a little neater and more durable.
- Fold a narrow hem, about 1/4 inch (6 mm), to the wrong side. Some sewists fold it twice for a cleaner finish.
- Use the same zigzag settings, or lengthen slightly to about 1–1.5 mm, because you’re sewing through more layers.
- Sew over the fold with the right swing of the needle landing at or just over the folded edge.
- Stretch evenly as you sew, as in Method 1.
- Trim any excess hem allowance close to the stitching on the wrong side, if you like.
Troubleshooting lettuce hems
| Problem | Try this |
|---|---|
| Edge doesn’t ripple much | Stretch harder and more evenly; check you’re sewing along the greatest stretch; use a fabric with more spandex |
| Fabric jams or bunches under the foot | Lengthen the stitch slightly; use an open-toe or satin foot; hold the thread tails as you start |
| Fabric chewed into the needle plate | Start a little in from the corner; start on a strip of tear-away stabilizer |
| Uneven ripple | Move your hands more often; keep the same amount of stretch all the way along |
| Thread breaks | Use a new needle and good-quality polyester thread; sew slower |
| Skipped stitches | Switch to a stretch or jersey needle |
For more on stitch and tension behaviour on knits, see tension settings and stretch stitches for knit fabric.
Making gathered ruffles on a sewing machine
For a gathered ruffle, cut the strip longer than the edge it will be sewn to. Somewhere between one and a half and three times the length is common, depending on how full you want it. Finish the ruffle’s outer edge (narrow hem, rolled hem or fold) before gathering.
Two rows of basting
This is the most controllable method and works on almost any fabric.
- Set the longest straight stitch your machine has. Leave the tension at default, or loosen it slightly.
- Leave long thread tails and don’t backstitch.
- Sew one row just inside the seam line, and a second row parallel to it a short distance away, within the seam allowance.
- Pull the two bobbin threads together from one end, sliding the fabric along to gather it. Work from both ends on long ruffles.
- Distribute the gathers evenly, pin to the main piece, and sew with a normal stitch length between or just beside the basting rows.
- Remove any basting that shows on the right side.
Zigzag over a cord
This method is good for long ruffles or heavier fabric, where gathering threads tend to snap.
- Lay a strong cord (crochet cotton, buttonhole twist or dental floss) along the seam allowance.
- Sew over it with a wide zigzag that doesn’t catch the cord.
- Slide the fabric along the cord to gather it. The cord won’t break, and you can pull it out after the ruffle is sewn on.
Gathering foot and ruffler attachment
- A gathering foot gathers light fabric as you sew. Longer stitches and higher upper tension give more fullness. Some can gather one layer and attach it to a flat layer at the same time.
- A ruffler attachment is a mechanical device that pushes small pleats or tucks into the fabric at set intervals, such as every stitch, every 6th stitch or every 12th stitch, depending on the model. It’s worth having if you make a lot of ruffles. Check that it matches your machine’s shank type (low, high or slant) before buying.
There’s also a quick method that turns the upper tension high with a long stitch, so light fabric gathers on its own. It’s fast, but harder to control, and it doesn’t work well on heavier fabric. Remember to set the tension back afterwards.
Why is there a loop under my sewing machine?
Loops or a “bird’s nest” of thread on the underside of the fabric almost always point to the top thread, not the bobbin. The most common cause is that the machine was threaded with the presser foot down, so the thread isn’t seated between the tension discs. To fix it:
- Raise the presser foot.
- Remove the top thread completely and rethread, following the machine’s thread path.
- Make sure the take-up lever is threaded.
- Check that the bobbin is inserted the right way round for your machine.
If you’ve deliberately loosened tension for gathering, set it back to default before normal sewing, or you’ll see loops on regular seams too.
For more on sewing knits in general, see our guide to sewing stretchy and tricky fabrics on a sewing machine.