Fabrics and Needles

How to Sew Sequin Fabric With a Sewing Machine

Machine-sew sequin fabric without broken needles: check the nap, clear sequins from seam allowances, pick needle and stitch settings, then finish and press safely.

On this page
  1. Can you use a sewing machine for sequins?
  2. Know your sequin fabric
  3. Tools and machine setup
  4. Cutting sequin fabric
  5. Clearing sequins from the seam allowance
  6. Sewing the seams
  7. Hems, edges and linings
  8. Pressing and finishing
  9. Can sequin fabric be altered?
  10. Troubleshooting

Can you use a sewing machine for sequins?

Yes. You can sew sequin fabric, meaning sequins already stitched onto a mesh, knit or woven base, on an ordinary home sewing machine. The trick is preparation. Before you sew, remove the sequins from the seam allowances so the needle sews through the base fabric, not through hard plastic.

Attaching individual loose sequins is a different job. That’s normally done by hand, or with specialist embroidery attachments or machines.

Sequin fabric is often listed among the harder fabrics to sew, mainly because the prep is slow. The machine sewing itself is fairly straightforward once the seam lines are clear.

Know your sequin fabric

Check two things before you buy a pattern or cut anything:

  • The base fabric. Sequins may be sewn onto:
    • non-stretch mesh, tulle or woven fabric, which behaves like a woven;
    • stretch mesh or a knit, which needs stretch-friendly needle and stitch choices.
  • The nap. Run your hand down the fabric. In one direction the sequins lie smooth, like fish scales. In the other they catch and stand up. Usually you cut every piece so the sequins point downwards on the finished garment. Mark the nap direction on the wrong side.

Simple designs with few seams and darts are much easier in sequin fabric than complex ones.

Tools and machine setup

  • Needle: a new Microtex (sharp) 70/10 or 80/12 for non-stretch mesh or woven bases, or a stretch or jersey 75/11–90/14 for stretch bases. Expect to change it during the project, because sequins dull needles.
  • Stitch: a straight stitch about 3–3.5 mm long for non-stretch bases, or a narrow zigzag or stretch stitch for stretch bases.
  • Thread: all-purpose polyester.
  • Foot: a standard foot often works. A non-stick (Teflon-type) foot or a walking foot can help if the sequins drag.
  • Old scissors: sequins dull blades, so don’t use your best fabric shears.
  • Small sharp scissors or a seam ripper for removing sequins.
  • Clips rather than lots of pins.
  • Eye protection while cutting and while sewing near sequins, in case a sequin or needle fragment flies up.
  • A serger is generally not recommended. The knives can be damaged by cutting through sequins.

Cutting sequin fabric

  1. Cut in a single layer, wrong side up, with every pattern piece facing the same nap direction.
  2. Trace around the pattern on the wrong side with chalk or a marker, including the seam lines, not just the cutting lines.
  3. Cut slowly with old scissors. Expect loose sequins to scatter. Work over a sheet or tray so they’re easy to collect.
  4. Save the loose sequins. You’ll use some later to patch bare spots.

Clearing sequins from the seam allowance

This is the step that makes machine sewing possible.

  1. Mark the seam line on each piece.
  2. Remove sequins from the seam allowance, plus a little past the seam line, so the needle won’t hit any. You can:
    • snip each sequin in half with small scissors and pull the halves away, or
    • cut the threads holding them and slide them off, or
    • crush them carefully with pliers on some types (test first).
  3. Secure the thread chain. On many sequin fabrics the sequins are sewn on with a continuous chain stitch that can unravel once cut. Put a small dab of fabric glue or seam sealant at the ends, or hand-tack the chain, to stop more sequins coming loose.
  4. Repeat on hem allowances, darts and anywhere else you’ll stitch.

This is slow, so leave plenty of time. A bodice can take longer to clear than to sew.

Sewing the seams

  1. Sew a test seam on scraps prepared the same way.
  2. Clip the layers right sides together.
  3. Sew slowly, especially near the edges of the cleared area. If the needle sounds like it’s hitting something hard, stop and turn the handwheel by hand to check.
  4. Don’t pull the fabric. Let the feed dogs work, so the needle isn’t forced sideways into a sequin.
  5. Finish the seam allowances if the base frays. A zigzag or overcast stitch on the cleared allowance is fine. A lining will hide them anyway.

Hems, edges and linings

  • Hems: clear the hem allowance, fold it up and hand-catch it in place. Alternatively, face the hem with a strip of lining fabric or satin bias binding, which also stops the hem scratching the legs.
  • Necklines and armholes: a facing or full lining in a soft fabric is far more comfortable than exposed sequin edges, which can be scratchy.
  • Lining: cut the lining from the same pattern and attach it at the neckline and armholes. Some sewists bag the lining for a clean finish.

Pressing and finishing

  • Don’t press sequins with a hot iron. Many sequins are plastic and can melt, warp or lose their shine.
  • Finger-press the seams, or press from the wrong side with a low heat setting and a press cloth, testing on a scrap first.
  • Fill bare spots: turn the garment right side out and look along the seams. Hand-sew a few of your saved sequins over any bald strip next to the seam line, so the seam virtually disappears.
  • Trim threads and check for any sequins hanging loose by a thread.

Can sequin fabric be altered?

Usually yes, but it takes more care than altering plain fabric:

  • Taking a seam in: unpick the seam, mark the new seam line, clear sequins from the new allowance, then sew as above. Keep the removed sequins to patch the new seam.
  • Letting a seam out is only possible if there’s enough seam allowance, and the old stitching holes may show on the base fabric.
  • Shortening: clear sequins from the new hem allowance and re-hem by hand.
  • Heavily beaded or embellished garments are often best taken to a professional alterations service.

Troubleshooting

Problem Likely cause Fix
Needle breaks or bends Hitting a sequin Clear more sequins from the allowance; sew slower; replace the needle
Skipped stitches Dull needle; wrong type for a stretch base New Microtex or stretch needle
Fabric won’t feed Sequins dragging on the foot or feed dogs Non-stick or walking foot; tissue paper under the layers
Bald strip along the seam Too many sequins removed Hand-sew saved sequins back over the gap
Sequins falling off near seams Chain-stitch thread unravelling Seal or hand-tack thread ends after clearing

For the other fabrics in this family, such as stretch knits, leather and vinyl, see our hub on sewing stretchy and tricky fabrics, or check the needle sizes and types chart.

The complete guide to fabrics and needles

Sewing Stretchy and Tricky Fabrics on a Sewing Machine
Read the guide

Keep exploring

Guides from other topics

All topics →