Divide both the elastic and the fabric edge into quarters and pin them together at the marks. Then sew with a zigzag or three-step zigzag, stretching the elastic between the pins so it lies flat against the fabric as it goes under the needle. When you let go, the fabric gathers evenly. Use a jersey or stretch needle and polyester thread. Choose the method below that suits your garment: a casing, sewn-on elastic, fold-over elastic, or clear elastic for stabilising seams.
Before you start: elastic type, length, needle and stitch
Elastic types:
- Knitted elastic: soft, stays fairly narrow when stretched, good for waistbands sewn directly to fabric.
- Braided elastic: narrows when stretched; usually best inside a casing rather than sewn through.
- Woven (non-roll) elastic: firm, resists rolling; good for waistbands on trousers and skirts.
- Fold-over elastic (FOE): has a centre line for folding over an edge like binding.
- Lingerie and picot elastic: soft, often with a decorative edge, for underwear and bras.
- Clear (polyurethane) elastic: thin and very stretchy; used to stabilise seams and in swimwear.
Length: elastic is normally cut shorter than the edge it’s going on, so the edge gathers slightly and grips. Follow your pattern if it gives a length. If not, wrap the elastic around the body where it will sit, pull it comfortably snug, and add an overlap for joining. Try it on before sewing it shut.
Needle and thread: a jersey or stretch needle (75/11–90/14), and polyester thread. See which needle to use for stretchy fabric and thread for stretch fabric.
Stitch: a zigzag (try about 3–4 mm wide, 2–3 mm long) or a three-step zigzag, which stays flatter and is less likely to make the elastic ripple. Avoid a straight stitch on exposed elastic, because it will break when stretched.
Quarter-marking: the key to even gathers
- Join the elastic into a loop (if it’s a waistband) or keep it as a strip (for leg openings or necklines).
- Fold the elastic in half, then in half again, and mark the four quarter points with pins or a fabric marker.
- Do the same on the fabric edge. Side seams and centre front and back often make convenient quarter marks.
- Pin the elastic to the fabric at matching marks. For long edges, mark eighths for more control.
Between each pair of pins, the elastic has to stretch to match the fabric. That’s what spreads the gathers evenly.
Method 1: elastic in a casing
This is the easiest method and works with any elastic, especially braided.
- Fold the top edge of the garment over to form a channel slightly wider than the elastic, and sew it down with a stretch stitch or narrow zigzag. Leave a gap of a few centimetres.
- Attach a safety pin to one end of the elastic and feed it through the channel. Pin the trailing end so it can’t disappear inside.
- Check that the elastic isn’t twisted all the way round.
- Overlap the ends by about 2.5 cm (1 inch) and sew them together securely (see “Joining elastic ends” below).
- Ease the elastic inside and sew the gap closed, stretching the fabric flat as you sew.
- Optional: topstitch through the casing and elastic in one or more rows to stop the elastic twisting. Stretch the waistband flat in front of and behind the foot as you sew, and let the feed dogs move it.
Method 2: sewn-on elastic (attach and flip)
This is common on activewear, underwear, and pyjama and lounge waistbands. The elastic is sewn directly to the fabric.
- Quarter-mark and pin the elastic to the wrong side of the fabric, edge to edge (or to the right side for lingerie, following your pattern).
- First pass: zigzag along the edge, stretching the elastic between pins so it lies flat on the fabric. Don’t stretch the fabric itself.
- Flip: fold the elastic to the inside, so the fabric wraps around it.
- Second pass: sew again from the right side with a zigzag, three-step zigzag or twin needle, catching the elastic’s other edge. Stretch as before.
If you have a serger, the first pass is often done on the serger, and the second on the sewing machine.
Method 3: fold-over elastic
FOE binds an edge in one go and looks neat on necklines, armholes and baby clothes.
- If your pattern includes a seam allowance on that edge, trim it off. FOE wraps around the raw edge.
- Quarter-mark both the FOE and the fabric edge.
- Fold the FOE along its centre line around the fabric edge, and clip or pin it.
- Sew close to the inner edge of the FOE with a zigzag, stretching the elastic slightly as you go so the edge sits flat on the body.
- Some sewists baste the FOE to one side first with a long stitch, then fold and zigzag. Remove the basting afterwards, because a straight basting stitch won’t stretch.
Method 4: clear elastic to stabilise seams
On jersey tops, shoulder seams can stretch out over time. Clear elastic stops this while still allowing a little stretch.
- Cut clear elastic to the length of the seam. Don’t stretch it for stabilising, unless your pattern says to.
- Lay it over the seam allowance and sew it in with the seam, using a narrow zigzag or serger.
- Trim close to the stitching.
Clear elastic is also used at swimwear leg and neck openings, stretched slightly while sewing. It can be slippery under the foot, so sew slowly.
Joining elastic ends
- Overlap method: overlap the ends by about 2.5 cm (1 inch) and sew a box, or several rows of zigzag, through both layers.
- Butt join (flatter): butt the ends together over a small scrap of fabric and zigzag across the join. This avoids a thick lump. Useful for wide elastic or close-fitting garments.
Sew the elastic ends together before attaching it, unless you’re using a casing.
Troubleshooting
| Problem | Likely cause | Fix |
|---|---|---|
| Waistband ripples or looks wavy | Fabric stretched instead of elastic; uneven stretching | Quarter-mark more finely; stretch only the elastic |
| Elastic feels loose after sewing | Elastic lost recovery from too many needle holes or too-dense stitching | Lengthen the stitch; use a three-step zigzag; try a firmer elastic |
| Stitches break when stretched | Straight stitch or cotton thread | Zigzag or three-step zigzag; polyester thread |
| Skipped stitches through elastic | Wrong needle or a worn needle | New stretch needle, possibly one size larger |
| Elastic twists inside a casing | Not secured | Topstitch through the casing; stitch in the ditch at side seams |
| Gathers bunched in one area | Uneven distribution | Use quarter- or eighth-marks; check gathers before the final pass |
For more on stretch stitches and machine settings for knits, see tension settings and stretch stitches for knit fabric. For the full setup for sewing knits, see sewing stretchy and tricky fabrics on a sewing machine.