Fabrics and Needles

Can I sew denim on a regular sewing machine?

Yes, most home machines sew denim with a jeans needle, longer stitch and slow speed over thick seams. Here's the setup, hemming tips and signs your machine is struggling.

On this page
  1. What a regular machine can and can’t handle
  2. Setup for sewing denim
  3. Getting over thick seams
  4. Hemming jeans on a home machine
  5. Topstitching denim
  6. Stretch denim
  7. Signs your machine is struggling

Yes. Most regular home sewing machines can sew denim, especially light and medium-weight denim in one or two layers. Use a jeans needle (90/14 or 100/16), lengthen the stitch to about 3–3.5 mm, and slow right down, turning the handwheel by hand, over thick seam intersections. The hard parts are the bulky spots where many layers meet, such as side seams at a hem, belt loops and flat-felled seams.

What a regular machine can and can’t handle

  • Usually fine: sewing seams in light and medium denim, hemming most bought jeans, patches, denim bags and skirts.
  • Possible with care: hems on heavy jeans, belt loops, flat-felled seams, heavy topstitching thread.
  • Often too much: very heavy (raw or selvedge-weight) denim in many layers, and very thick bonded threads. Small lightweight “mini” machines can struggle even with ordinary jeans hems.

Your machine’s manual may list a maximum needle size or fabric thickness. If it doesn’t recommend 100/16 or 110/18 needles, take that as a hint about its limits.

Setup for sewing denim

  1. Needle: a new jeans needle, size 90/14 for light denim or 100/16 for jeans-weight denim and multi-layer seams. A 100/16 is a good default for jeans. See needles for denim and canvas for the full sizing table.
  2. Thread: good-quality all-purpose polyester for construction seams.
  3. Stitch length: about 3–3.5 mm. Longer stitches look better on thick fabric and are less likely to jam.
  4. Tension: start at your machine’s default. On thick fabric some sewists find they need to raise the upper tension slightly. On a dial machine such as a Singer, that’s often half a number to a number above default. Test on a folded scrap with the same number of layers and adjust until the stitch looks balanced on both sides.
  5. Presser foot pressure: default or slightly higher, if adjustable, so thick layers are held firmly against the feed dogs.
  6. Clips: pins struggle with many layers of denim. Use sewing clips on thick sections.

Getting over thick seams

Thick ridges cause most denim problems. When the foot tilts up over a bulky seam, the feed dogs lose grip, and stitches bunch up or the needle breaks.

  • Flatten the seam first. Press it with steam, and if needed tap the bulk with a hammer, protecting the denim with a scrap of fabric. This compresses the fibres and makes a real difference.
  • Trim and grade seam allowances inside the garment, where possible, to remove layers.
  • Level the foot with a hump jumper, a plastic shim, or a folded piece of denim placed under the back of the foot as you climb onto the seam, and under the front as you come down. This keeps the foot parallel to the feed dogs.
  • Slow down or hand-crank. Sew right up to the bulky section, then turn the handwheel by hand, one stitch at a time, until you’re over it.
  • Don’t push or pull the fabric through. That can bend the needle into the needle plate.

Hemming jeans on a home machine

  1. Mark and cut the new length, leaving a hem allowance of about two folds’ worth (for example, two folds of about 1/2 inch / 1.25 cm each).
  2. Press the double fold firmly with steam. Hammer the side-seam areas flat.
  3. Clip the hem, especially at the side seams.
  4. Start sewing on the inseam side, at the back, so any join in the stitching is less visible.
  5. Use the hump jumper and hand-crank over each side seam.
  6. Overlap a few stitches at the end rather than backstitching through all the layers.

For a “factory” look, use topstitching thread in the needle with a topstitch or 100/16 jeans needle (see below).

Topstitching denim

  • Thick topstitching (jeans) thread in the needle, with regular all-purpose thread in the bobbin. Bobbins usually don’t handle heavy thread well.
  • A topstitch needle, which has a larger eye, or a 100/16 jeans needle.
  • A longer stitch, about 3.5–4 mm, so the thicker thread shows nicely.
  • Topstitch from the right side, and test the tension on a scrap of folded denim. You may need to raise the upper tension a little with thick thread.
  • If your machine refuses to cooperate with heavy thread, try the triple straight stitch with ordinary thread. It gives a bold line using regular thread.

Stretch denim

Denim with elastane needs a seam that can give:

  • use a narrow zigzag (around 1–1.5 mm wide) or a stretch stitch for seams that take strain;
  • try a jeans needle first, and switch to a stretch needle if stitches skip;
  • the triple stitch makes very strong seams on stretch denim, but it’s hard to unpick. See tension settings and stretch stitches for knit fabric for what each stretch stitch does.

Many mechanical heavy-duty machines, such as the Singer Heavy Duty range, are marketed for denim and handle jeans well with this setup. Thick cross-seams still need slow, careful sewing.

Signs your machine is struggling

Stop and reassess if you notice:

  • the motor straining, slowing or humming without the needle moving;
  • the needle bending, deflecting or breaking repeatedly;
  • skipped stitches only at thick spots, even with a new jeans needle;
  • the fabric refusing to feed even with a hump jumper;
  • a burning smell or the machine getting unusually hot.

Fewer layers, a larger needle (if supported), and hand-cranking through the worst spots solve most of these. If not, the job may be beyond that machine. Pushing it can damage the timing or the motor.

For other heavy and awkward fabrics, see our guide to sewing stretchy and tricky fabrics and the needle sizes and types chart.

The complete guide to fabrics and needles

Sewing Stretchy and Tricky Fabrics on a Sewing Machine
Read the guide

Keep exploring

Guides from other topics

All topics →