Short Answer
The right settings depend on which part of quilting you’re doing, but these are common starting points:
- Piecing: straight stitch, about 2.0–2.5 mm stitch length, 1/4-inch foot, feed dogs up.
- Straight-line quilting with a walking foot: about 3.0–3.5 mm stitch length, feed dogs up, presser foot pressure reduced slightly if your machine allows.
- Free-motion quilting: feed dogs down (or covered), free-motion foot fitted. Stitch length is set by how fast you move the quilt.
- Needle and thread: a fresh 80/12 needle for piecing and 90/14 for quilting, with 40wt or 50wt thread.
- Tension: start at your machine’s default and adjust only after testing on a scrap quilt sandwich.
Numbers vary between brands and models. One machine’s “3.0” may look slightly different from another’s, so treat these as starting points and test.
Quick-Reference Settings Table
| Setting | Piecing | Walking-foot quilting | Free-motion quilting | Machine binding |
|---|---|---|---|---|
| Stitch | Straight | Straight (or serpentine) | Straight | Straight |
| Stitch length | ~2.0–2.5 mm | ~3.0–3.5 mm | Set by hand speed | ~2.5–3.5 mm |
| Feed dogs | Up | Up | Down or covered | Up |
| Presser foot | 1/4-inch foot | Walking foot | Free-motion/darning foot | Walking foot or edge-stitch foot |
| Needle | 80/12 | 90/14 | 90/14 | 90/14 |
| Needle position | Adjust for accurate 1/4 inch | Center | Center | As needed for edge stitching |
| Speed | Comfortable | Moderate and steady | Steady, often medium–fast | Slow at corners |
Settings for Piecing
- Stitch length: around 2.0–2.5 mm. Shorter stitches stop seams opening at the ends when they’re crossed by other seams or trimmed, but very short stitches are hard to unpick.
- Foot: a 1/4-inch foot, with or without an edge guide.
- Needle position: some quilters move the needle one or two steps to the right to sew a “scant” 1/4 inch. See our guide on how to sew an accurate 1/4-inch seam to calibrate yours.
- Thread: 50wt cotton or polyester in a neutral color is a common choice. Finer thread takes up less room in the seam.
- Straight-stitch plate: if your machine has one, it can reduce fabric being pushed into the needle hole at the start of seams. Only use it with a straight stitch at center needle position. Using it with a zigzag or offset needle can break the needle.
Settings for Straight-Line (Walking Foot) Quilting
- Stitch length: around 3.0–3.5 mm. Longer stitches look neater on top of a thick sandwich and are less likely to make the quilt draw up. Very long stitches can catch when the quilt is used.
- Foot: a walking foot or built-in dual feed, so the top layer feeds at the same rate as the bottom.
- Feed dogs: up.
- Presser foot pressure: if your machine has an adjustment, lowering it slightly can help thick layers feed without the top shifting ahead. Check your manual for the recommended range.
- Needle: 90/14.
- Needle-down: on, so the quilt stays put when you pause.
For technique, see our guide to quilting straight lines with a walking foot.
Settings for Free-Motion Quilting
- Feed dogs: lowered, or covered with a cover plate. On some machines that can’t drop their feed dogs, setting the stitch length to 0 helps.
- Foot: a free-motion, darning or hopping foot.
- Stitch length: not set by the machine. Your hand speed relative to the needle speed decides it. (Machines with a stitch regulator are the exception.)
- Speed: many quilters find a steady, moderately fast needle speed easier than a slow one.
- Tension: often needs a small adjustment compared with regular sewing. Test first.
Our free motion quilting guide covers setup and practice in detail.
Settings for Machine Binding
- Stitch length: around 2.5–3.5 mm. Matching the length of your quilting stitches can look tidy.
- Foot: a walking foot helps the layers feed evenly. Some quilters prefer an edge-stitch foot for the final topstitching.
- Thread: top thread to match the binding, bobbin thread to match the backing.
- Needle position: moving the needle left or right can help you stitch a consistent distance from the folded edge.
Our tutorial on how to bind a quilt entirely by machine covers the full process.
Tension: How to Test and Adjust
Most modern machines sew well at their default tension for ordinary sewing, but quilting often calls for small adjustments.
When to test:
- At the start of every new quilt
- After changing thread, needle or bobbin
- After switching between walking-foot and free-motion quilting
- After turning the machine off and on, if your machine resets its settings
How to test:
- Make a scrap sandwich from the same fabric, batting and thread as your quilt.
- Stitch straight lines, and for free motion, curves and sharp points too. Curves and points show tension problems most clearly.
- Inspect both sides.
Reading the results:
- Balanced: stitches look the same on both sides, and the threads lock inside the batting.
- Top tension too loose: the top thread shows on the back as loops, or as “eyelashes” around curves.
- Top tension too tight: bobbin thread shows as dots on top, and the stitches on the back look strained or flat.
Adjusting: change the top tension in small steps, and change only one thing at a time. Before changing tension at all, rethread the top with the presser foot up and check the bobbin is correctly seated. Threading errors cause many apparent tension problems. On most home machines, leave bobbin case tension alone unless your manual says otherwise.
Presser Foot Pressure
Not every machine has an adjustable presser foot pressure. If yours does, reducing it slightly for thick quilt layers can stop the top layer being pushed ahead, which causes ripples and tucks. Reduce it in small steps. With too little pressure, the fabric won’t feed well. Your manual will show the scale and the default for your model.
Needles and Thread
- Change the needle at the start of each quilt, and whenever stitches start skipping or the needle makes a punching sound.
- Match the needle to the thread. Thicker threads need a larger eye. A topstitch needle is a common choice for 40wt or heavier threads.
- Use quality thread. Linty or uneven thread can cause tension trouble and breakage.
- Bobbin thread: many quilters use the same thread top and bottom while learning. Matching the bobbin thread to the backing fabric can hide small tension imperfections.
Helpful Machine Functions to Turn On
- Needle-down: keeps the quilt in place when you stop or pivot.
- Speed limiter: a moderate maximum speed gives more control.
- Knee lifter: keeps both hands on the quilt while you raise the foot.
- Lock or tie-off stitch: useful for securing line ends, though many quilters prefer to bury thread tails by hand on visible areas.
A Pre-Quilting Checklist
- Clean lint from the bobbin area and feed dogs.
- Fit a new needle of the right size and type.
- Wind full bobbins.
- Thread the machine with the presser foot up.
- Attach the correct foot for the task.
- Set feed dogs up or down as needed.
- Set stitch length and needle position.
- Adjust presser foot pressure if needed.
- Stitch a test sandwich and check both sides.
- Adjust tension in small steps, then start quilting.
For the bigger picture of piecing, basting, quilting and binding at home, see our main guide to quilting on a domestic sewing machine.